<!doctype linuxdoctr system>

<!--
	v1.08 add warning about rc.S 'ro' test
	v1.07 add generic 'linuxrc' and raid5 support
	v1.06 add 'rm /etc/mtab' to fail over rescue boot
		in 'linuxrc'
 	v1.05 upgrade to linuxthreads-0.71
	v1.04 initial release
-->

<article>

<!-- Title information -->
<title>Root RAID HOWTO cookbook
<author>Michael A. Robinton, <url url="mailto:michael@bzs.org"
				name="michael@bzs.org">
<date>v1.08, April 02, 1998
<trans>藤原輝嘉, <url url="mailto:fjwr@mtj.biglobe.ne.jp"
                            name="fjwr@mtj.biglobe.ne.jp">
<tdate>3 May 1998
<abstract>
<!--
This document provides a cookbook for creating a root mounted raid
filesystem and companion fallback rescue system using linux initrd. There
are complete step-by-step instruction for both raid1 and raid5 md0 devices. 
Each step is accompanied by an explanation of it's purpose.
Included with this revision is a generic <bf/linuxrc/ initrd file which may
be configured with a single three line <ref id="raidboot-conf"
name="/etc/raidboot.conf"> file for
raid1 and raid5 configurations.
-->
この文書では RAID で構成したファイルシステムをルートディレクトリとして
マウントするための方法と，Linux の initrd を使って対になる fallback 復
旧システムを作るための方法を述べます．RAID1 と RAID5 の md0 デバイスを
使用する完全な手順を示します．手順の各ステップと一緒にその目的も説明
します．この版は RAID1 と RAID5 の設定向けの，3つの行で設定される
<ref id="raidboot-conf" name="/etc/raidboot.conf"> ファイルに合わせて
設定した一般的な <bf/linuxrc/ initrd ファイルを含んでいます．

</abstract>
<!-- Table of contents -->
<toc>

<sect>はじめに
<!-- Introduction -->

<p>
<!--
The reader is assumed to be familiar with the various types of raid
implementations, their advantages and drawbacks. This is not a tutorial,
just a set of instructions on how to implement root mounted raid on a linux
system. All
of the information necessary to become familiar with linux raid is listed
here directly or by reference, please read it before send e-mail questions.
-->
読者は色々なタイプの RAID の実装とそれらの利点や欠点をよくわかっている
ものと仮定します．本文書はチュートリアルではなく，Linux システムで 
RAID をルートにマウントする方法の手順だけを示すものです．Linux の RAID 
について知るために必要な情報は全て文書内で直接示すか，参考文献として示
しています．ですから私に質問のメールを送るのはそれらをよく調べた上で行っ
てください．

<sect1>本文書の最新版の入手
<!-- Where to get Up-to-date copies of this document. -->

<p>
Root-RAID-HOWTO
<p>
<!--
Available in LaTeX (for DVI and PostScript), plain text, and HTML.
-->
LaTeX (DVI や PostScript を作れます)，テキスト，HTML の各フォーマット
で入手できます．

<quote>	<url url="http://sunsite.unc.edu/mdw/HOWTO/"
	name="sunsite.unc.edu/mdw/HOWTO/">
</quote>
<!--
Available in SGML and HTML.
-->
SGML と HTML 形式で入手できます．
<quote>	<url url="ftp://ftp.bizsystems.com/pub/raid/"
	name="ftp.bizsystems.com/pub/raid/">
</quote>

<sect1>バグ
<!-- Bugs -->
<p>
<!--
As of this writing, the problem of stopping a root mounted RAID device has
not yet been solved in a satisfactory way.  A work-around proposed by Ed
Welbon and implemented by Bohumil Chalupa is incorporated into this document
which eliminates the need for a long ckraid at each boot for raid1 and raid5
devices. Without the workaround, it is necessary to <bf/ckraid/ the <bf/md/ device 
each time the system is re-booted. On a large array this can cause a severe
availability performance degradation.  On my 6 gig RAID1 device running on a
Pentium 166 with 128 megs of ram, it takes well over half an hour to ckraid
:-(
after each re-boot. It takes over an hour on my 13 gig RAID5 array with a
20mb/sec scsi adaptor.
-->
この文書を書いている時点で，ルートにマウントした RAID デバイスが停止す
る問題は完全には解決されていません．Ed Welbon さんが提案し，Bohumil
Chalupa さんが実装した回避方法はこの文書に含まれています．これは RAID1 
と RAID5 デバイスの場合に，毎ブート時の長い ckraid コマンドが必要では
なくなるというものです．この回避方法を行わないと，システムを再起動する
度に <bf/md/ デバイスに対して <bf/ckraid/ が必要となります．これだと大
きなアレイの場合には，システムの性能が大幅に低下してしまいます．筆者の 
Pentium 166, メモリ 128M のシステム上で動作している 6G の RAID1 デバイ
スでは，再起動の度に ckraid に30分以上もかかってしまいます :-( 転送速
度 20MB/秒の SCSI アダプタに接続している 15ギガバイトの RAID5 アレイの
場合は1時間以上かかります．
<p>
<!--
The workaround stores the status of the array at 
shutdown on the <bf/real/ boot device and compares it to a reference status
placed there when the system is first built. If the status's match at
reboot, the superblock on the array is rebuilt on the next boot, otherwise 
the operator is notified of the status error and the rescue system is left
running with all the raid tools available.
-->
回避方法というのは，シャットダウン時にアレイの状態を<bf/実際の/ブート
デバイスに保存して，ここに置いてある最初にシステムを構築した時の参照
ステータスと比較するものです．ステータスが再起動のときに一致していれば
アレイのスーパーブロックは次のブート時に再構築され，そうでなければオペ
レータにステータスエラーを通知し，全ての RAID ツールが使用可能な 
復旧システムが残されます．
<p>
<!--
Rebuilding the superblock causes 
the system to ignore that the array was powered down without mdstop by 
marking all the drives as <bf/OK/, as if nothing happened. This only works if
all the drives are OK at shutdown. If the array was operating with a bad
drive, the operator must remove the bad drive prior to restarting the md
device or the data can be corrupted.
-->
スーパーブロックを再構築することで，全てのドライブに<bf/OK/の印を付け
られてしまい，mdstop を実行せずにアレイの電源が切られたことがシステム
に無視されることが起こります．これは全てのドライブのステータスがシャッ
トダウン時にOKである場合しか正しく動作しません．異常があるドライブでア
レイが動いている場合には，md デバイスを再スタートさせる前に異常なドライ
ブを取り除く必要があり，そうでなければデータが壊れてしまうことがありま
す．
<p>
<!--
None of this applies to raid0 which 
does not have to be mdstopped before shutdown.
-->
RAID0 の場合はシャットダウン前に mdstop を行う必要が無いので，上記のこ
とはいずれもあてはまりません．

<!--
Final proposed solutions to this problem include a <bf/finalrd/ similar to
<bf/initrd/, and <bf/mdrootstop/ which writes the <bf/clean/ flags to the array 
during  shutdown when it is mounted read only. I am sure there are others.

In the mean time, the problem has been by-passed for now 
Please let me know when this problem is solved more cleanly!!!
-->
この問題に対して最終的に提案された解は，<bf/initrd/ に似た 
<bf/finalrd/ と，デバイスがリードオンリーの時はシャットダウン中に
<bf/clean/ フラグを書き込む <bf/mdrootstop/を導入することです．
他の方法もきっとはあることでしょう．

とにかく，今のところは問題を避けることはできています．
この問題をもっとうまく解決されたらぜひ私にお知らせください．

<sect1>謝辞
<!-- Acknowledgements -->

<p>
<!--
The writings and e-mail from the following individuals helped to make this
document possible.  Many of the ideas were <it/stolen/ from the helpful work of
others, I have just tried to put it all in <bf/COOKBOOK/ form so that it is
straightforward to use. My thanks to:
-->
以下の方々の文書やメールのおかげでこの文書が完成しました．アイディアの
ほとんどは他の人のものを<it/もらってきた/もので，私はこれらを
<bf/COOKBOOK/の形にまとめ，すぐに使えるようにしただけです．
<!--
<itemize>
<item><url name="Linas Vepstas" url="mailto:linas@linas.org">
	<it> for the RAID howto that explained most of this to me.</it>
<item><url name="Gadi Oxman" url="mailto:gadio@netvision.net.il">
	<it> for answering my dumb 'newbie' questions.</it>
<item><url name="Ed Welbon" url="mailto:welbon@bga.com">
	<it> for the execellent <bf/initrd.md/ package that inspired me to write this.</it>
<item><url name="Bohumil Chalupa"
url="mailto:bochal@apollo.karlov.mff.cuni.cz"> <it> for implementing the
re-boot 'workaround' that allows
</it> <bf>root-mounted-raid</bf><it> to
work in a production environment.</it>
<p>
<item>and many others who contributed to this work in one way or another.
</itemize>
-->
<itemize>
<item><url name="Linas Vepstas さん" url="mailto:linas@linas.org">
	<it> の RAID HOWTO でほとんどのことを勉強させていただきました．</it>
<item><url name="Gadi Oxman さん" url="mailto:gadio@netvision.net.il">
	<it> には「素人」のくだらない質問に答えていただきました．</it>
<item><url name="Ed Welbon さん" url="mailto:welbon@bga.com">
	<it> の素晴らしい <bf/initrd.md/ パッケージがきっかけでこの文
書を書くことになりました．</it>
<item><url name="Bohumil Chalupa さん"
url="mailto:bochal@apollo.karlov.mff.cuni.cz"> <it> が再起動時の「問題
回避」を実装してくださったおかげで，
</it> <it>仕事の環境で</it><bf>RAID をルートにマウントして</bf><it>使
えるようになりました．</it>
<p>
<item>この他に色々な点この作業を助けてくださった方々．
</itemize>

<sect1>著作権表示
<!-- Copyright Notice -->

<p>
This document is GNU copyleft by Michael Robinton
<url url="mailto:michael@bzs.org" name="michael@bzs.org">.
<p>
        Permission to use, copy, distribute this document for any
        purpose is hereby granted, provided that the author's / editor's
        name and this notice appear in all copies and/or supporting
        documents; and that an unmodified version of this document is
        made freely available.  This document is distributed in the hope
        that it will be useful, but WITHOUT ANY WARRANTY, either
        expressed or implied.  While every effort has been taken to
        ensure the accuracy of the information documented herein, the
        author / editor / maintainer assumes NO RESPONSIBILITY for any
        errors, or for any damages, direct or consequential, as a result
        of the use of the information documented herein.

<sect>作業を始める前に必要な事項
<!-- What you need BEFORE YOU START -->

<p>
<!--
The packages you need and the documentation that answers the most common
questions about setting up and running raid are listed below. Please review
them throughly.
-->
RAID を設定し，運用するために必要なパッケージや，ほとんどの疑問に答え
てくれる文書を以下に示します．簡単にでも良いですからこれらの資料には目
を通してください．

<sect1>必要なパッケージ
<!-- Required Packages -->

<p>
<!--
You need to obtain the most recent versions of these packages.
-->
まずは以下のパッケージの最新のバージョンを入手する必要があります．

<!--
<itemize>
<item>a linux kernel that supports raid, initrd and /dev/loopx
<quote>	I used <url name="linux-2.0.33"
	url="ftp://sunsite.unc.edu/pub/Linux/kernel/">
	from sunsite</quote>
<item><url name="raid145-971022-2.0.31"
	url="ftp://ftp.kernel.org/pub/linux/daemons/raid/">
	patch adds support for raid1/4/5
<item><url name="raidtools-pre3-0.42"
	url="ftp://ftp.kernel.org/pub/linux/daemons/raid/">
	tools to create and maintain
	raid devices (documentation too).
<item><ref id="Appendix-E" name="Gadi's raid stop patch"> in Appendix E.
<item><url name="linuxthreads-0.71"
	url="ftp://ftp.inria.fr/INRIA/Projects/cristal/Xavier.Leroy">
	required threads package. Use ftp, browser doesn't work
ftp.inria.fr/INRIA/Projects/cristal/Xavier.Leroy
<item>A Linux distribution, ready to install.
<quote>	I used <url name="Slackware-3.4" url="ftp://ftp.cdrom.com/pub/linux">
</quote>
</itemize>
-->
<itemize>
<item>RAID, initrd, /dev/loopx をサポートしている Linux カーネル
<quote>	筆者は <url name="linux-2.0.33"
	url="ftp://sunsite.unc.edu/pub/Linux/kernel/">
	を sunsite から入手しました．</quote>
<item><url name="raid145-971022-2.0.31"
	url="ftp://ftp.kernel.org/pub/linux/daemons/raid/">
	RAID1/4/5 のサポートを追加するパッチです．
<item><url name="raidtools-pre3-0.42"
	url="ftp://ftp.kernel.org/pub/linux/daemons/raid/">
	RAID のデバイスを作成，管理するためのツール(と文書)です．
<item><ref id="Appendix-E" name="Gadi 氏の RAID 停止パッチ"> を付録 E に含めています．
<item><url name="linuxthreads-0.71"
	url="ftp://ftp.inria.fr/INRIA/Projects/cristal/Xavier.Leroy">
	スレッドのパッケージが必要です．ウェブブラウザは使えないので 
FTP をつかってください．
<item>インストールできる Linux のディストリビューション
<quote>	筆者は <url name="Slackware-3.4" url="ftp://ftp.cdrom.com/pub/linux">
を使っています．</quote>
</itemize>

<!--
Helpful but not required
-->
必要ではないけれど，役立つもの
<!--
<itemize>
<item><url name="raidboot-0.01.tar.gz"
url="ftp://ftp.bizsystems.com/pub/raid/">
	pre-built raid rescue/boot system.
</itemize>
-->
<itemize>
<item><url name="raidboot-0.01.tar.gz"
url="ftp://ftp.bizsystems.com/pub/raid/">
	予め作成されている RAID 復旧/起動システム
</itemize>
<p>
<!--
The detailed instructions in this document are based on the above packages.
If the packages have been updated or you use a different linux distribution,
you may have to modify the procedures you find here.
-->
本文書における具体的な手順は上記のパッケージを前提にしています．パッケー
ジのバージョンが更新されていたり，私と異なる Linux のディストリビュー
ションを使っている場合には，具体的な手順を異なるかもしれません．
<p>
<!--
The patches, tool assortment, etc... may vary with 2.1 kernels.
Please check the most recent documentation at:
-->
パッチやツール等はバージョン 2.1 のカーネルでは異なる場合があります．
最新の文書を以下で確認してください．

<quote><url url="ftp://ftp.kernel.org/pub/linux/daemons/raid/"
	name="ftp.kernel.org/pub/linux/daemons/raid/"></quote>

<sect1>他の類似の実装系
<!-- Other similar implementations. -->

<p>
<!--
I chose to include in the kernel all of the pieces necessary 
to run from boot without loading any modules.  My kernel image is
a little over 300k compressed.
-->
私はモジュールは使わないで，必要なものは全てカーネルに組み込むことにし
ました．私のカーネルイメージの大きさは，圧縮して 300k と少しです．

<!--
Take a look at <url name="Ed Welbon's" url="mailto:welbon@bga.com">
<bf/initrd.md.tar.gz/ for another
way to make a bootable raid device.  He uses loadable modules. 
A look at his concise scripts will show you how it is done
if you need a very small kernel with modules.
-->
起動可能な RAID デバイスを作る別の方法として，<url name="Ed Welbon 氏"
url="mailto:welbon@bga.com"> の <bf/initrd.md.tar.gz/ を見てください．
こちらの方法ではモジュールを使っています．モジュールを使ってとても小さ
いカーネルを作りたい場合には，このパッケージに含まれる簡単なスクリプト
を見れば，どうすればよいかわかります．

<quote><url url="http://www.realtime.net/~welbon/initrd.md.tar.gz"
name="http://www.realtime.net/~welbon/initrd.md.tar.gz"></quote>

<sect1>ぜひ読んでおきたい文書
<!-- Documentation  Recommended Reading -->

<p>
<!--
<bf/Please read:/
<quote><bf>/usr/src/linux/Documentation/initrd.txt</bf></quote>
-->
まず<quote><bf>/usr/src/linux/Documentation/initrd.txt</bf></quote>
は読んでください．

<p>
<!--
as well as the documentation and man pages that accompany 
the raidtools set. In particular, read <bf/man mdadd/ as well as the
<bf/QuickStart.RAID/ document included in the raidtools package.
-->
それから raidtools パッケージに付属の文書やマニュアルも読んでください．
特に <bf/man mdadd/ と <bf/QuickStart.RAID/ には目を通してください．

<p>
<!--
You may also wish to review:
-->
以下のものにも目を通しておくと良いでしょう．
<itemize>
<item><url url="http://sunsite.unc.edu/mdw/HOWTO/BootPrompt-HOWTO.html"
   name="BootPrompt-HOWTO">
<item><bf/man lilo/
<item><bf/man lilo.conf/
</itemize>

<sect1>RAID 関連の情報
<!-- RAID resources -->

<p>
<itemize>
<item><url url="http://sunsite.unc.edu/mdw/HOWTO/mini/Software-RAID"
	name="sunsite.unc.edu/mdw/HOWTO/mini/Software-RAID">
<item><url url="http://www.ssc.com/lg/issue17/raid.html"
	name="www.ssc.com/lg/issue17/raid.html">
<item><url url="http://linas.org/linux/raid.html"
	name="linas.org/linux/raid.html">
<item><url url="ftp://ftp.kernel.org/pub/linux/daemons/raid/"
	name="ftp.kernel.org/pub/linux/daemons/raid/">
<item><url url="http://www.realtime.net/~welbon/initrd.md.tar.gz"
	name="www.realtime.net/~welbon/initrd.md.tar.gz">
<item><url url="http://luthien.nuclecu.unam.mx/~miguel/raid/"
	name="luthien.nuclecu.unam.mx/~miguel/raid/">
</itemize>
<!--
Mailing lists can be joined at:
-->
関係があるメーリングリストを以下に列挙します．
<!--
<itemize>
<item><url name="majordomo@nuclecu.unam.mx"
	url="mailto:majordomo@nuclecu.unam.mx"><it> send a message to</it>
	<bf/subscribe raiddev/<p>
	send mail to: <url name="raiddev@nuclecu.unam.mx"
	url="mailto:raiddev@nuclecu.unam.mx">
<item><url name="majordomo@vger.rutgers.edu"
	url="mailto:majordomo@vger.rutgers.edu"><it> send a message to</it>
	<bf/subscribe linux-raid/<p>
	send mail to: <url name="linux-raid@vger.rutgers.edu"
	url="mailto:linux-raid@vger.rutgers.edu">
	<it>(this seems to be the most active list)</it>
</itemize>
-->
<itemize>
<item><url name="majordomo@nuclecu.unam.mx"
	url="mailto:majordomo@nuclecu.unam.mx"><it> へ</it>
	<bf/subscribe raiddev/<it>の内容のメールを送れば参加できます．</it><p>
	投稿は <url name="raiddev@nuclecu.unam.mx"
	url="mailto:raiddev@nuclecu.unam.mx"> へメールを送ります．
<item><url name="majordomo@vger.rutgers.edu"
	url="mailto:majordomo@vger.rutgers.edu"><it>へ</it>
	<bf/subscribe linux-raid/<it>の内容のメールを送れば参加できます．</it><p>
	投稿は <url name="linux-raid@vger.rutgers.edu"
	url="mailto:linux-raid@vger.rutgers.edu"> へメールを送ります．
	<it>(これが最も活発なメーリングリストのようです)</it>
</itemize>

<sect>ルートディレクトリを RAID にする方法の概説
<!-- Quick Start for ROOT RAID -->
<p>
<!--
If you don't want to try and build and debug the rescue system, you can get
a generic one created from Slackware-3.4 from:
-->
復旧システムを試したり，構築したり，デバッグしたくない場合は，
Slackware-3.4 に基づいて作った一般的なシステムを以下で入手してください．
<quote><url url="ftp://ftp.bizsystems.com/pub/raid/"
	name="ftp.bizsystems.com/pub/raid/raidboot-0.01.tar.gz">
</quote>
<!--
Perform the following steps:
-->
そして，次の手順を実行します．
<!--
<itemize>
<item>Compile the raid enabled kernel with 
built in support for your disk subsystem
<item>Test that the raid array will configure and mount correctly
<item>Build your OS on the raid system
<item>Correct the entries in <bf/fstab/ to show <bf>/dev/md0</bf> as the
root device. Make sure that the partition(s) you use for booting are included in
<bf/fstab/. 
<item>Modify your shutdown halt and reboot script(s) (mine is /etc/rc.d/rc.6) as shown in 
<ref id="modify_shutdown" name="Modifying the rc-scripts for SHUTDOWN">
<item>Copy the following from you development filesystem
to the rescue system AND the new raid system

<verb>
	cd /root/raidboot
	mkdir mnt
	gzip -d rescue.clean
	losetup /dev/loop0  rescue.clean
	mount /dev/loop0    mnt

copy these files

	cp -p /etc/*         mnt/etc
	cp -p /etc/rc.d/*    mnt/etc/rc.d 
		{or as appropriate for your system}
	cp -a /lib/modules/* mnt/lib/modules 
</verb>
Some Linux distributions include a test for the <bf>ro/rw</bf> status of the
root file system. The <bf/rc startup/ files need to
have this test removed for the initrd rescue system. See the instructions in
the section on <ref id="corrections" name="Correctons for Rescue System">.
</itemize>
-->
<itemize>
<item>使用するディスクのサポートを組み込み，RAID を有効にしたカーネル
を構築します
<item>RAID アレイが正しく設定，マウントできるかテストします
<item>RAID システム上に OS をインストールします
<item>ルートデバイスとして <bf>/dev/md0</bf> を参照するように 
<bf/fstab/ の内容を修正します．起動に必要なパーティションが <bf/fstab/ 
に含まれていることを確認します．
<item>Modify your shutdown halt and reboot script(s) (mine is /etc/rc.d/rc.6) as shown in 
<ref id="modify_shutdown" name="Modifying the rc-scripts for SHUTDOWN">
の記述にしたがって，マシンの停止及び再起動のスクリプト(筆者のシステム
では /etc/rc.d/rc.6 です)を修正します．
<item>以下の手順に示すように，ファイルを作業用システムから，復旧システ
ムと新しい RAID システムの両方にコピーします．
<verb>
	cd /root/raidboot
	mkdir mnt
	gzip -d rescue.clean
	losetup /dev/loop0  rescue.clean
	mount /dev/loop0    mnt

次のようにファイルをコピーします．

	cp -p /etc/*         mnt/etc
	cp -p /etc/rc.d/*    mnt/etc/rc.d 
		{or as appropriate for your system}
	cp -a /lib/modules/* mnt/lib/modules 
</verb>
Linux のディストリビューションによっては，ルートファイルシステムの 
<bf>ro/rw</bf> ステータスを調べます．initrd 復旧システムの <bf/rc 起動/
スクリプトからは，これを調べる部分を取り除く必要があります．<ref
id="corrections" name="復旧システムの修正">の章の手順を参照してくださ
い．
</itemize>
<!--
Correct the entries in <bf/fstab/ to show <bf>/dev/md0</bf> as the root
device. Make sure that the partition(s) you use for booting is included in
<bf/fstab/.
-->
<bf/dev/md0/ がルートデバイス<bf/fstab/ になるよう <bf/fstab/ を修正し
ます．起動に必要なパーティションが <bf/fstab/ に含まれていることを確認
しましょう．
<p><label id="raidboot-conf">
<!--
Create <bf>/etc/raidboot.conf</bf> which describes the raid boot
configuration. This file may <bf/NOT/ contain comments in the first three
lines, after that it doesn't matter.
-->
RAID から起動する設定を記述する <bf>/etc/raidboot.conf</bf> を作成しま
す．このファイルの最初の3行にはコメントを入れてはいけません．それ以降
ならば問題ありません．
<p>
raidboot.conf
<verb>
	/dev/sda1 /dev/sda2
	raidboot
	raid5.conf
# comments may only be placed 'after' the three
# configuration lines.
#
# This is 'raidboot.conf'
#
# line one, the partition(s) containing the 'initrd' raid-rescue system
#       It is not necessary to boot from these partitions, however,
#       since the rescue system will not fit on floppy, it is necessary
#       to know which partitions are to be used to load the rescue system
#
# line two, the path to the raidboot config information
#       Where the shutdown status, etc... is located at boot time
#       It does NOT include the mount point information, only 'path'
#       /mntpoint/'path'
#
# line -3-, name of the raid configuration file
#       Current raid configuration file i.e. raid1.conf, raid5.conf
</verb>
<!--
A few more things to do and the raid systems is ready to boot.
-->
後はいくつかの作業を行えば，RAID システムの起動準備ができます．
<p>
<!--
Create <ref id="Appendix-F" name="rc.raidown">, as described in Appendix F,
and copy it to /etc/rc.d on the rescue, development, and raid system.
Unmount the rescue system and zip it.
-->
付録 F で説明する，<ref id="Appendix-F" name="rc.raidown"> ファイルを
# 作成し，これを復旧，作業，RAID の各システムの /etc/rc.d ディレクトリ
# にコピーします．復旧システムをアンマウントした後，これを圧縮します．
<verb>
	umount mnt
	losetup -d /dev/loop0
	mv rescue.clean rescue
	gzip rescue
</verb>
<!--
Copy the rescue file to the raidboot partitions.
-->
復旧ファイルを RAID 起動パーティションにコピーします．
<verb>
	cp rescue.gz /mnt_point(1)/raidboot
	cp rescue.gz /mnt_point(2)/raidboot
</verb>
<!--
Activate the raid array.
-->
RAID アレイを有効にします．
<verb>
	mdadd -ar
</verb>
<!--
Save the <bf/good/ reference status to the raidboot partition
-->
RAID 起動パーティションの <bf/正しい/ 参照ステータスを保存します．
<verb>
	cat /proc/mdstat | grep md0 > /mnt_point(1)/raidboot/raidgood.ref
        cat /proc/mdstat | grep md0 > /mnt_point(1)/raidboot/raidgood.ref
</verb>
<!--
Lastly, configure the boot program as outlined in <ref id="raidboot-conf"
name="Boot Time Configuration Parameters"> and reboot your system onto the
raid array.
-->
最後に <ref id="raidboot-conf" name="起動時の設定パラメータ"> の説明に
従って起動プログラムを設定し，RAID アレイ上のシステムを起動します．

<sect>RAID をルートとしてマウントするための <it>initrd</it> の解説
<!-- <it>initrd</it> Cookbook for root mounted RAID -->

<p>
<!--
This is the procedure to make an 'initrd' ramdisk with rescue tools for raid.
-->
これは RAID の復旧ツール(rescue tools) を含む `initrd' RAMディスクを
作るための手続きです．

<p>
<!--
Specifically, this document referrs to RAID1 and RAID5 implementations.
-->
本文書では特に RAID1 と RAID5 の実装について説明を行います．
<sect1>セキュリティに関する注意事項
<!-- Security Reminder -->

<p>
<!--
The rescue file system may be used stand alone. Should your raid array 
fail to mount, you are left with the rescue system mounted and running. 
TAKE THE APPROPRIATE SECURITY PRECAUTIONS!!!
-->
復旧用のファイルシステムはスタンドアロンで使用できます．RAID アレイの
マウントに失敗した場合，復旧システムがマウントされて動作します．
<bf/ですからセキュリティには十分注意してください！/

<sect1>カーネルと RAID ツールの構築
<!-- Build the Kernel and Raid Tools -->

<p>
<!--
The first thing that must be done is to patch and build your kernel
and become familiar with the raid tools. Make sure and include 
<ref id="Appendix-E" name="Gadi's raid stop patch"> in Appendix E.
Configure, mount and test your raid device(s). The details of how to do this
are included in the <bf/raidtools/ package and briefly reviewed later in
this document.
-->
最初の作業は，パッチを当ててカーネルを再構築することと RAID 操作ツール
に慣れることです．付録 E の
<ref id="Appendix-E" name="Gadi 氏の RAID 停止パッチ"> を確認し，カー
ネルに含めてください．設定を行ってから RAID デバイスをマウント，テスト
します．詳細な手順は <bf/raidtools/ パッケージに含まれていますが，本文
書でも後で述べます．

<sect1><it/initrd/ による復旧及び起動ファイルシステムの構築
<!-- Build the <it/initrd/ Rescue and Boot filesystem -->

<p>
<!--
I used the <bf/Slackware-3.4/ distribution to build both the Rescue/Boot
filesystem and the filesystem for the production machine. Any linux
distribution should work fine. If you use a different distribution, review
the Slackware specific portion of this procedure and modify it to suit your needs.
-->
私は復旧/起動用のファイルシステムと仕事用のマシンのファイルシステムを
構築する際に <bf/Slackware-3.4/ ディストリビューションを使いました．で
すが，どの Linux ディストリビューションでも問題ないと思います．異なる
ディストリビューションを使う場合には，手順のうち Slackware に特化した
部分を確認し，必要に応じて修正してください．

<p>
<!--
I use loadlin to boot the kernel image and ramdisk from a dos partition
simply because there are oddball devices in my system that have dos
configuration software. Lilo will work just as well and a small linux
partition can be used instead containing only the raid/boot files and the
<bf/lilo/ record.
-->
筆者は loadlin を使ってカーネルイメージとRAMディスクを DOS パーティショ
ンから起動していますが，これは，単に DOS の設定ソフトウェアを使う困っ
たデバイスを使っているからです．LILO でもうまく動作しますし，RAID/起動
ファイルと <bf/lilo/ レコードだけを含む小さい Linux パーティションも使
用できます．

<!--
For the raid boot/rescue system, 
I chose to create a minimum ramdisk system using the Slackware 'setup' 
script followed by installing the 'linuxthreads' package and 'raidtools'
over the clean Slackware installation on my ramdisk. I used the
<it><bf/identical/</it> procedure to build the production system. So the
rescue and production systems are very similar.
-->
筆者は最初に Slackware の `setup' スクリプトを使って最小限のRAMディス
クシステムを作り，次にこのRAMディスク上の素のSlackware に 
`linuxthreads' パッケージと `raidtools' を上書きインストールすることに
しました．私は仕事用のマシンを構築するときにも<bf/全く同じ/手続きを用
いました．ですから，復旧システムと仕事用システムはほぼ同じ構成になって
います．

<p>
<!--
This installation process gives me a 'bare' system 
(save a copy of the file) to which I overlay
-->
このインストールによって`裸の'システムができます(ファイルのコピーを保
存しておきましょう)．このシステムへ

<verb>	/lib/modules/2.x.x......
	/etc .... with a modified fstab, mdtab, raidX.conf, raidboot.conf
	/etc/rc.d
	/dev/md*</verb>
<p>
<!--
from my current system to customize it for the particular kernel
and machine that it is/will-be running on.
-->
を現在使っているシステムから上書きコピーし，現在あるいはこれから動作さ
せようとしているシステムに合わせてカスタマイズします．

<p>
<!--
This makes the boot/rescue system the same system that is running
on the root mounted raid device, just skinnyed down a bit, while 
allowing the library, etc... revisions to always be current.
-->
これにより，起動/復旧システムを現在動作している RAID デバイスをルート
にマウントしたシステムと同じにできます．ライブラリ等のバージョンは常に
最新にできますが，少し小さいシステムになります．

<sect1>ステップ・バイ・ステップの手順
<!-- Start the STEP by STEP instructions -->

<p>
<!--
From the root home directory (/root):
-->
ユーザ root のホームディレクトリ(/root)で以下のコマンドを実行します:

<verb>	cd /root
	mkdir raidboot
	cd raidboot</verb>
<p>
<!-- Create a mountpoints to work on -->
マウントポイントを作成します．

<verb>	mkdir mnt
	mkdir mnt2</verb>

<p>
<!--
Make a file large enough to do the file system install. This
will be a lot larger than the final rescue file system. 
I chose 24 megs since 16 megs is not large enough 
-->
ファイルシステムをインストールするのに十分な大きさのファイルを作ります．
これは最終的な復旧ファイルシステムよりずっと大きくなります．16メガバイ
トでは十分ではなかったので，私は24メガバイト使うことにしました．
<verb>
	dd if=/dev/zero of=build bs=1024k count=24
</verb>
<!--
associate the file with a loop device
and generate an ext2 file system on the file
-->
ファイルを loop デバイスとし，ext2 ファイルシステムをこのファイル上に
作成します．

<verb>	losetup /dev/loop0 build
	mke2fs -v -m0 -L initrd /dev/loop0
	mount /dev/loop0 mnt
</verb>
<sect1>ディストリビューションのインストール (Slackware の場合のみ)
<!-- Install the distribution - Slackware Specific -->
<p>
<!--
<ref id="threads" name="...skip Slackware Specific stuff">
and go to next section.
-->
Slackware にしか通用しない話題なので，Slackware 以外のディストリビュー
ションを使う場合には<ref id="threads" name="次の章に進んで">ください．
<p>
<!--
Now that an empty filesystem is created and mounted, run "setup".
-->
現在は空のファイルシステムが作られてマウントされている状態です．
ここで"setup"を実行します．
<p>
<!--
<verb>Specify		/root/raidboot/mnt</verb>
<p>
as the <bf/'target'/.  The source is whatever you normally install from.
Select the packages you wish to install and proceed but <bf/DO NOT/ configure.
-->
<bf/'target'/ には
<p>
<verb>	/root/raidboot/mnt</verb>
<p>
を指定します．`source'には通常のインストール元を適宜指定します．パッケー
ジ選択は自由に行ってかまいませんが，`configure' は<bf/行わないでください/．
<p>
<!--
Choose 'EXPERT' prompting mode.
-->
プロンプトのモードとしては `EXPERT' を選択します．
<p>
<!--
I chose 'A', 'AP, and 'N' installing only the minimum to run the system 
plus an editor I am familiar with (vi, jed, joe) that is reasonably compact.
-->
私はシステムの最小構成の `A', `AP', `N' に加え，使い慣れていてサイズも
小さいエディタ(vi, jed, joe)を選択しました．
<verb>
lqqqqqqqq SELECTING PACKAGES FROM SERIES A (BASE LINUX SYSTEM) qqqqqqqqk
x lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk x
x x   [X] aaa_base  Basic filesystem, shell, and utils - REQUIRED    x x
x x   [X] bash      GNU bash-1.14.7 shell - REQUIRED                 x x
x x   [X] devs      Device files found in /dev - REQUIRED            x x
x x   [X] etc       System config files &amp; utilities - REQUIRED       x x
x x   [X] shadow    Shadow password suite - REQUIRED                 x x
x x   [ ] ide       Linux 2.0.30 no SCSI (YOU NEED 1 KERNEL)         x x
x x   [ ] scsi      Linux 2.0.30 with SCSI (YOU NEED 1 KERNEL)       x x
x x   [ ] modules   Modular Linux device drivers                     x x
x x   [ ] scsimods  Loadable SCSI device drivers                     x x
x x   [X] hdsetup   Slackware setup scripts - REQUIRED               x x
x x   [ ] lilo      Boots Linux (not UMSDOS), DOS, OS/2, etc.        x x
x x   [ ] bsdlpr    BSD lpr - printer spooling system                x x
x x   [ ] loadlin   Boots Linux (UMSDOS too!) from MS-DOS            x x
x x   [ ] pnp       Plug'n'Play configuration tool                   x x
x x   [ ] umsprogs  Utilities needed to use the UMSDOS filesystem    x x
x x   [X] sysvinit  System V-like INIT programs - REQUIRED           x x
x x   [X] bin       GNU fileutils 3.12, elvis, etc. - REQUIRED       x x
x x   [X] ldso      Dynamic linker/loader - REQUIRED                 x x
x x   [ ] ibcs2     Runs SCO/SysVr4 binaries                         x x
x x   [X] less      A text pager utility - REQUIRED                  x x
x x   [ ] pcmcia    PCMCIA card services support                     x x
x x   [ ] getty     Getty_ps 2.0.7e - OPTIONAL                       x x
x x   [X] gzip      The GNU zip compression - REQUIRED               x x
x x   [X] ps        Displays process info - REQUIRED                 x x
x x   [X] aoutlibs  a.out shared libs - RECOMMENDED                  x x
x x   [X] elflibs   The ELF shared C libraries - REQUIRED            x x
x x   [X] util      Util-linux utilities - REQUIRED                  x x
x x   [ ] minicom   Serial transfer and modem comm package           x x
x x   [ ] cpio      The GNU cpio backup/archiving utility            x x
x x   [X] e2fsbn    Utilities for the ext2 file system               x x
x x   [X] find      GNU findutils 4.1                                x x
x x   [X] grep      GNU grep 2.0                                     x x
x x   [ ] kbd       Change keyboard mappings                         x x
x x   [X] gpm       Cut and paste text with your mouse               x x
x x   [X] sh_utils  GNU sh-utils 1.16 - REQUIRED                     x x
x x   [X] sysklogd  Logs system and kernel messages                  x x
x x   [X] tar       GNU tar 1.12 - REQUIRED                          x x
x x   [ ] tcsh      Extended C shell version 6.07                    x x
x x   [X] txtutils  GNU textutils-1.22 - REQUIRED                    x x
x x   [ ] zoneinfo  Configures your time zone                        x x
x mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj x
</verb>
<!--
From the 'AP series, I use only 'JOE', and editor I like, and 'MC' a
small and useful file management tool. You choose the utilities you
will need on your system.
-->
`AP' シリーズからは私の好きなエディタ `JOE' とコンパクトで便利なファイ
ル操作ツールである `MC' だけを選択しました．ここは必要に応じてユーティ
リティを選択してください．
<verb>
lqqqqqqqqq SELECTING PACKAGES FROM SERIES AP (APPLICATIONS) qqqqqqqqqk
x x     [ ] ispell    The International version of ispell          x x
x x     [ ] jove      Jonathan's Own Version of Emacs text editor  x x
x x     [ ] manpgs    More man pages (online documentation)        x x
x x     [ ] diff      GNU diffutils                                x x
x x     [ ] sudo      Allow special users limited root access      x x
x x     [ ] ghostscr  GNU Ghostscript version 3.33                 x x
x x     [ ] gsfonts1  Ghostscript fonts (part one)                 x x
x x     [ ] gsfonts2  Ghostscript fonts (part two)                 x x
x x     [ ] gsfonts3  Ghostscript fonts (part three)               x x
x x     [ ] jed       JED programmer's editor                      x x
x x     [X] joe       joe text editor, version 2.8                 x x
x x     [ ] jpeg      JPEG image compression utilities             x x
x x     [ ] bc        GNU bc - arbitrary precision math language   x x
x x     [ ] workbone  a text-based audio CD player                 x x
x x     [X] mc        The Midnight Commander file manager          x x
x x     [ ] mt_st     mt ported from BSD - controls tape drive     x x
x x     [ ] groff     GNU troff document formatting system         x x
x x     [ ] quota     User disk quota utilities                    x x
x x     [ ] sc        The 'sc' spreadsheet                         x x
x x     [ ] texinfo   GNU texinfo documentation system             x x
x x     [ ] vim       Improved vi clone                            x x
x x     [ ] ash       A small /bin/sh type shell - 62K             x x
x x     [ ] zsh       Zsh - a custom *nix shell                    x x
x mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj x
</verb>
<!--
From the 'N' package I only loaded TCPIP.  This isn't really necessary, 
but is very handy and allows access to the network while working on a 
repair or update with the root raid array dismounted. TCPIP also 
contains 'biff' which is used by some of the applications in 'A'. If 
you don't install 'N' you might want to install the biff package anyway.
-->
`N' パッケージからは TCP/IP だけを入れました．これは必ずしも必要ではあ
りませんが，非常に便利ですし，ルートに RAID アレイがマウントされていな
い状態で復旧や更新の作業を行う際にネットワークにアクセスできるようにな
ります．TCP/IP には `A' に含まれるアプリケーションのいくつかが使用する 
`biff' も含んでいます．`N' をインストールしなかったとしても，biff パッ
ケージは入れたくなると思います．
<verb>
lqqqq SELECTING PACKAGES FROM SERIES N (NETWORK/NEWS/MAIL/UUCP) qqqqqk
x lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk x
x x    [ ] apache    Apache WWW (HTTP) server                      x x
x x    [ ] procmail  Mail delivery/filtering utility               x x
x x    [ ] dip       Handles SLIP/CSLIP connections                x x
x x    [ ] ppp       Point-to-point protocol                       x x
x x    [ ] mailx     The mailx mailer                              x x
x x    [X] tcpip     TCP/IP networking programs                    x x
x x    [ ] bind      Berkeley Internet Name Domain server          x x
x x    [ ] rdist     Remote file distribution utility              x x
x x    [ ] lynx      Text-based World Wide Web browser             x x
x x    [ ] uucp      Taylor UUCP 1.06.1 with HDB &amp;&amp; Taylor configs x x
x x    [ ] elm       Menu-driven user mail program                 x x
x x    [ ] pine      Pine menu-driven mail program                 x x
x x    [ ] sendmail  The sendmail mail transport agent             x x
x x    [ ] metamail  Metamail multimedia mail extensions           x x
x x    [ ] smailcfg  Extra configuration files for sendmail        x x
x x    [ ] cnews     Spools and transmits Usenet news              x x
x x    [ ] inn       InterNetNews news transport system            x x
x x    [ ] tin       The 'tin' news reader (local or NNTP)         x x
x x    [ ] trn       'trn' for /var/spool/news                     x x
x x    [ ] trn-nntp  'trn' for NNTP (install 1 'trn' maximum)      x x
x x    [ ] nn-spool  'nn' for /var/spool/news                      x x
x x    [ ] nn-nntp   'nn' for NNTP (install 1 'nn' maximum)        x x
x x    [ ] netpipes  Network pipe utilities                        x x
x mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj x
</verb>
<!--
With the installation complete, say no to everything else (no to all
configuration requests) and exit the script.
-->
インストールが終了したら，それ以外の項目には全て `no' と答え(全ての設
定項目に `no' と答える)，スクリプトを終了します．

<sect1>Linux <bf/pthreads/ のインストール <label id="threads">
<!-- Install linux <bf/pthreads/<label id="threads"> -->

<p>
<!--
Now you must install the 'linuxthreads-0.71' library.
I have included this diff for the linuxthreads Makefile rather 
than explain the details of the
installation by hand.  Save the original Makefile, apply the diff
and then:
-->
次に`linuxthreads-0.71' ライブラリをインストールしなければなりません．
ここでは手作業によるインストールを詳しく説明する代わりに，linuxthreads 
の Makefile に対する差分パッチを示します．元の Makefile を保存してから 
diff コマンドでパッチを当て，そして make を行います．

<verb>	cd /usr/src/linuxthreads-0.71
  patch
	make
	make install
</verb><label id="thrdiff"><verb>
-------------------diff Makefile.old  Makefile.raid-----------------
2a3,13
> # If you are building "linuxthreads" for installation on a mount
> # point which is not the "root" partition, redefine 'BUILDIR' to
> # the mount point to use as the "root" directory
> # You may wish to do this if you are building an 'initial ram disk'
> # such as used with bootable root raid devices.
> # REQUIRES ldconfig version 1.9.5 or better
> # do ldconfig -v to check
> #
> BUILDIR=/root/raidboot/mnt
> #BUILDIR=
> 
81,82c92,93
<       install pthread.h $(INCLUDEDIR)/pthread.h
<       install semaphore.h $(INCLUDEDIR)/semaphore.h
---
>       install pthread.h $(BUILDIR)$(INCLUDEDIR)/pthread.h
>       install semaphore.h $(BUILDIR)$(INCLUDEDIR)/semaphore.h
84c95
<       test -f /usr/include/sched.h || install sched.h $(INCLUDEDIR)/sched.h
---
>       test -f $(BUILDIR)/usr/include/sched.h || install sched.h $(BUILDIR)$(INCLUDEDIR)/sched.h
86,89c97,103
<       install $(LIB) $(LIBDIR)/$(LIB)
<       install $(SHLIB) $(SHAREDLIBDIR)/$(SHLIB)
<       rm -f $(LIBDIR)/$(SHLIB0)
<       ln -s $(SHAREDLIBDIR)/$(SHLIB) $(LIBDIR)/$(SHLIB0)
---
>       install $(LIB) $(BUILDIR)$(LIBDIR)/$(LIB)
>       install $(SHLIB) $(BUILDIR)$(SHAREDLIBDIR)/$(SHLIB)
>       rm -f $(BUILDIR)$(LIBDIR)/$(SHLIB0)
>       ln -s $(SHAREDLIBDIR)/$(SHLIB) $(BUILDIR)$(LIBDIR)/$(SHLIB0)
> ifneq ($(BUILDIR),)
>       ldconfig -r ${BUILDIR} -n $(SHAREDLIBDIR)
> else
91c105,106
<       cd man; $(MAKE) MANDIR=$(MANDIR) install
---
> endif
>       cd man; $(MAKE) MANDIR=$(BUILDIR)$(MANDIR) install
</verb>

<sect1>RAID ツールのインストール
<!-- Install Raid Tools -->

<p>
<!--
The next step is the installation of the raid tools.
raidtools-0.42
-->
インストールの次のステップは，RAID ツール raidtools-0.42 のインストー
ルです．
<p>
<!--
You must run the "configure" script to point the Makefile
at the build directory for the ramdisk files
-->
RAMディスクのファイルを構築するディレクトリを Makefile に教えるために
"configure" スクリプトを実行します．
<verb>
  cd /usr/src/raidtools-0.42
  configure --sbindir=/root/raidboot/mnt/sbin --prefix=/root/raidboot/mnt/usr
  make
  make install
</verb>
<!--
Now!! the Makefile for install is not quite right so do the following
to clean up. This will be fixed in future releases so that the re-linking
will not be necessary.
-->
ここで注意すべき点があります．インストールに使う Makefile は正しくない
ので，これを直すために次の作業を行います．これは将来のリリースでは修正
され，再リンクは必要無くなる予定です．

<!-- <quote>Fix the make install error</quote> -->
<quote>インストールエラーの修正</quote>
<!--
The file links specified in the Makefile at 'LINKS' must be removed
and re-linked to operate properly.
-->
正しく操作するためには Makefile の `LINKS' で指定されているファイルの
リンクを削除し，張り直さなければなりません．
<verb>
	cd /root/raidboot/mnt/sbin
	ln -fs mdadd mdrun
	ln -fs mdadd mdstop
</verb>

<sect1>新しいファイルシステムからの不要なディレクトリとファイルの削除
<!-- Remove un-needed directories and files from new filesystem. -->

<p>
<!--
Delete the following directories from filesystem 
(CAUTION DON'T DELETE FROM YOUR RUNNING SYSTEM)
it's easy to do, guess how I found out!!!
-->
以下のディレクトリとファイルをファイルシステムから削除します．
(<bf/注意: 誤って現在稼働中のシステムのファイルを消さないように/．)
このリストを見てファイルを消すだけなら簡単ですが，私がこのリストをどう
やって作ったのかも考えてください！
<verb>
	cd /root/raidboot/mnt
	rm -r home/ftp/*
	rm -r lost+found
	rm -r usr/doc
	rm -r usr/info
	rm -r usr/local/man
	rm -r usr/man
	rm -r usr/openwin
	rm -r usr/share/locale
	rm -r usr/X*
	rm -r var/man
	rm -r var/log/packages
	rm -r var/log/setup
	rm -r var/log/disk_contents
</verb>

<sect1>/dev/md<it/x/ の作成
<!-- Create /dev/md<it/x/ -->

<p>
<!--
The last step simply copies the /dev/md* devices from the current file system
onto the rescue file system.  You could create these with mknode.
-->
最後のステップは，現在のファイルシステムから復旧ファイルシステムに 
/dev/md* デバイスをただコピーすることです．これは mknod でも行うことが
できるでしょう．
<verb>
	cp -a /dev/md* /root/raidboot/mnt/dev
</verb>
<sect1><it/initrd/ のための裸のファイルシステム作成
<!-- Create a bare filesystem suitable for <it/initrd/ -->

<p>
<!--
Now you have a clean re-useable filesystem ready for customization. 
Once customized, this file system can be used for rescue should the raid
device(s) become corrupted and the raid tools needed to fix them. It will
also be used to boot and root-mount the raid device by adding the linuxrc
file which will be discussed next.
-->
これでカスタマイズでき，再利用も可能なまっさらなファイルシステムができ
ました．一度カスタマイズすると，復旧ディスクに使うことができるこのファ
イルシステムは壊れてしまい，修正するためにはRAIDツールが必要となります．
これは次の章で説明する linuxrc ファイルを追加することによって，ブート
してルートにマウントする RAID デバイスに使うこともできます．

<p>
<!--
Copy the file system to a smaller device for the initrd file,
16 megs should be large enough.
-->
initrd ファイルのために小さいデバイスへシステムをコピーします．16メガ
バイトもあれば十分でしょう．
<p>
<!--
Create the smaller file system and mount it
-->
小さいファイルシステムを作り，これをマウントします．
<verb>
	cd /root/raidboot
        dd if=/dev/zero of=bare.fs bs=1024k count=16
</verb>
<!--
associate the file with a loop device
and generate a ext2 file system on the file
-->
ファイルを loop デバイスとし，このファイル上に ext2 ファイルシステム構
築します．
<verb>
        losetup /dev/loop1 bare.fs
        mke2fs -v -m0 -L initrd /dev/loop1
        mount /dev/loop1 mnt2
</verb>
<!--
Copy the 'build' file system to 'bare.fs'
-->
`build'ファイルシステムを`bare.fs'にコピーします．
<verb>
	cp -a mnt/* mnt2
</verb>
<!--
Save the 'bare.fs' system before customization so later update is easy.
The 'build' file system is no longer needed and may be deleted.
-->
後の更新を容易にするため，カスタマイズの前に `bare.fs' システムを保存
します．`build' ファイルシステムはもう必要ありませんので，消しても構い
ません．
<verb>
	cd /root/raidboot
	umount mnt
	umount mnt2
	losetup -d /dev/loop0
	losetup -d /dev/loop1
	rm build
	cp bare.fs rescue
	gzip -9 bare.fs
</verb>
<sect2>起動/復旧用の <it><bf/initrd/</it> ファイルシステムの作成
<!-- Create the BOOT/RESCUE <it><bf/initrd/</it> filesystem -->

<p>
<!--
Now copy the system dependent items that match the kernel from the
development platform, or you can manually modify the files in the
rescue file system to match your target system.
-->
次に，作業用のマシンからカーネルに適合するシステム依存のファイルをコピー
するか，ターゲットのシステムに適合するように復旧ファイルシステムのファ
イルを手で修正するかします．
<verb>
	losetup /dev/loop0 rescue
	mount /dev/loop0 mnt
</verb>
<!--
Make sure your etc directory is clean of <tt/*~/, core and log files.
The next 2 commands creates some warning messages, ignore them.
-->
etc ディレクトリに <tt/*~/ ファイルや，core, ログファイルが無いことを
確認します．次の2つのコマンドはいくつかウォーニングを出しますが，無視
してください．
<verb>
	cp -dp /etc/* mnt/etc
	cp -dp /etc/rc.d/* mnt/etc/rc.d

	mkdir  mnt/lib/modules
	cp -a  /lib/modules/2.x.x mnt/lib/modules &lt;--- your current 2.x.x
</verb>
<sect2>復旧システムの修正 <label id="corrections">
<!-- Corrections for the Rescue System <label id="corrections"> -->
<p>
<!--
Edit the following files to correct them for your rescue system. Some file
names listed below are Slackware specific but have equivalents in other 
distributions.
-->
復旧システムの以下のファイルを修正します．ここで挙げるファイルの中には 
Slackware 特有のものもありますが，他のディストリビューションでも同等の
ものがあるはずです．
<!--
<verb>
	cd mnt

Non-network
	etc/fstab
	etc/mdtab	should work OK
Network
	etc/hosts
	etc/resolv.conf	
	etc/hosts.equiv		and related files
	etc/rc.d/rc.inet1	correct ip#, mask, gateway, etc...
	etc/rc.d/rc.S		remove entire section on file system status
		from:
			# Test to see if the root partition is read-only
		to but not including:
			# remove /etc/mtab* so that mount will .....
				This avoids the annoying warning that
				the ramdisk is mounted rw.
	etc/rc.d/rc.xxxxx	others as required, see later on in this doc
	root/.rhosts		if present
	home/xxxx/xxxx		others as required

    WARNING:	The above procedure moves your password and shadow
		files onto the rescue disk!!!!!

    WARNING:	You may not wish to do this for security reasons.
</verb>
-->
<verb>
	cd mnt

ネットワーク関係でないもの
	etc/fstab
	etc/mdtab	そのままで大丈夫でしょう
ネットワーク関係
	etc/hosts
	etc/resolv.conf	
	etc/hosts.equiv		及び関連ファイル
	etc/rc.d/rc.inet1	IPアドレス，ネットマスク，ゲイトウェイの設定を修正します
	etc/rc.d/rc.S		ファイルシステムのステータス関係の部分を全て削除します
			# Test to see if the root partition is read-only
		の部分から
			# remove /etc/mtab* so that mount will .....
		を含まない部分までを削除します．
				これは RAMディスクが読み書き可能でマウン
				トされると出るうるさいウォーニングを出
				ないようにします．
	etc/rc.d/rc.xxxxx	必要ならば他のファイルも．本文書で後述します
	root/.rhosts		もし存在すれば
	home/xxxx/xxxx		必要ならば他のファイルも

    警告:	この作業で passwd と shadow のファイルは復旧システムに
		コピーされてしまいます！これはセキュリティ上の理由で好
		ましくない場合もあるでしょう．
</verb>
<!--
Create any directories for mounting /dev/disk... as may be required
that are unique to your system.  These are the mountpoints for booting
the system (boot partition and backup boot partition). My system boot from
dos using <bf/loadlin/, however linux partition(s) and lilo will work fine.
My system uses:
-->
必要に応じて /dev/disk をマウントするためのディレクトリを作ります．
これはシステムで一意に決まらなければなりません．これらはシステムを起動
するためのマウントポイント(起動パーティションと起動パーティションのバッ
クアップ)になります．筆者のシステムは <bf/loadlin/ を利用して DOS から
起動するようになっていますが，Linux パーティションや LILO でもうまく動
作します．筆者のシステムでは以下のようになっています．
<!--
<verb>
	cd /root/raidboot/mnt		&lt;&mdash; initrd root
	mkdir dosa			dos partition mount point
	mkdir dosb			dos mirror mount point
</verb>
-->
<verb>
	cd /root/raidboot/mnt		&lt;&mdash; initrd のルート
	mkdir dosa			DOS パーティションのマウントポイント
	mkdir dosb			DOS のミラーのマウントポイント
</verb>
<!--
The rescue file system is complete!
-->
復旧ファイルシステムはこれで出来上がりです！
<p>
<!--
You will note upon examination of the files in the rescue file
system, that there are still many files that could be deleted.
I have not done this since it would overly complicate this 
procedure and most raid systems have adequate disk and memory.
If you wish to skinny down the file system, go to it!
-->
復旧ファイルシステムのファイルを調べれば，まだ多くのファイルを消せる
ことが分かると思います．この作業は複雑すぎることと，ほとんどの RAID シ
ステムには十分なディスクとメモリがあることから，私はこれを行ってはいま
せん．ファイルシステムをもっとスマートにしたければ，ご自分でやってくだ
さい！

<sect1> `initrd' で RAID デバイスから起動させる &ndash; linuxrc
<!-- Making 'initrd' boot the RAID device - linuxrc -->

<p>
<!--
To make the rescue disk boot the raid device, you need only copy
the executable script file:
-->
復旧ディスクで RAID デバイスを起動するには，ただ次のスクリプトファイル

<quote><bf/linuxrc/</quote>

<!--
to the root of the device.
-->
をデバイスのルートにコピーするだけです．
<p>
<!--
The theory of operation for this <bf/linuxrc/ file is discussed in 
<ref id="Appendix-G" name="Appendix G, linuxrc theory of operation">.
-->
この <bf/linuxrc/ ファイルの動作についての話は
<ref id="Appendix-G" name="付録 G, linuxrc の動作について">で議論しま
す．

<p>
<!--
A very simple and much easier to understand (working) linuxrc is
included in <ref id="Appendix-D" name="Appendix D">,
<it/obsolete linuxrc and shutdown scripts/. Copy the following text to
<bf/linuxrc/ and save in your development area.
-->
もっと簡単で理解しやすい(動作もする) linuxrc は <ref id="Appendix-D"
name="付録 D"> にありますが，<it/これは古い linuxrc と停止スクリプトで
す/．以下の部分を <bf/linuxrc/として作業ディレクトリにコピーしておきま
しょう．

<label id="linuxrc">
<verb>
 -------------------- linuxrc ----------------------
#!/bin/sh
# ver 1.13 3-6-98
#
################# BEGIN 'linuxrc' ##################
#                DEFINE FUNCTIONS                  #
####################################################
# Define 'Fault' function in the event something 
# goes wrong during the execution of 'linuxrc'
#
FaultExit () {
# correct fstab to show '/dev/ram0' for rescue system
    /bin/cat /etc/fstab | {
    while read Line
    do	
	if [ -z "$( echo ${Line} | /usr/bin/grep md0 )" ]; then
	    echo ${Line}
	else
	    echo "/dev/ram0 / ext2 defaults 1 1"
	fi
    done
    } > /etc/tmp.$$
    /bin/mv /etc/tmp.$$ /etc/fstab
#	point root at /dev/ram0 (the rescue system)
	echo 0x100>/proc/sys/kernel/real-root-dev
	/bin/umount /proc
	exit
}

# Define 'Warning' procdure to print banner on boot terminal
#
Warning () {
    echo '*********************************'
    echo -e " $*"
    echo '*********************************'
}

# Define 'SplitKernelArg' to help extract 'Raid' related kernel arguments
SplitKernelArg () { eval $1='$( IFS=,; echo $2)' }

#Define 'SplitConfArgs' to help extract system configuration arguments
SplitConfArgs () {
    RaidBootType=$1
    RaidBootDevice=$2
    RaidConfigPath=$3
}
########################################################
################### MAIN linuxrc #######################
########################################################
# mount the proc file system
/bin/mount /proc

# Get the boot partition and configuration location from command line
CMDLINE=`/bin/cat /proc/cmdline`
for Parameter in $CMDLINE; do
    Parameter=$( IFS='='; echo ${Parameter} )
    case $Parameter in
        Raid*) SplitKernelArg $Parameter;;
    esac
done

# check for 'required raid boot'
if [ -z "${Raid_Conf}" ]; then
    Warning Kernel command line \'Raid_Conf\' missing
    FaultExit
fi
SplitConfArgs $Raid_Conf

# tmp mount the boot partition
/bin/mount -t ${RaidBootType} ${RaidBootDevice} /mnt

# get etc files from primary raid system
pushd /etc

# this will un-tar into 'etc' (see rc.6)
if [ ! -f /mnt/${RaidConfigPath}/raidboot.etc ]; then
# bad news, this file should be here
    Warning required file \'raidboot.etc\' \
    missing from ${RaidBootDevice}/${RaidConfigPath} \\n \
    \\tUsing rescue system defaults
else
    /bin/tar -xf /mnt/${RaidConfigPath}/raidboot.etc
fi
# get 'real' raidboot device for this boot
# status path, and name of raidX.conf
if [ ! -f /mnt/${RaidConfigPath}/raidboot.cfg ]; then
# bad news, this file should be here
    Warning required file 'raidboot.cfg' \
    missing from ${RaidBootDevice}/${RaidConfigPath}\\n \
    \\tUsing rescue system defaults
# Get the first raidX.conf file name in $RArg1
    RaidBootDevs=$RaidBootDevice
    RaidStatusPath=$RaidConfigPath
    for RaidConfigEtc in $( ls raid*.conf )
    do break; done
else
    {
    read RaidBootDevs
    read RaidStatusPath
    read RaidConfigEtc
    } < /mnt/${RaidConfigPath}/raidboot.cfg

fi
popd
/bin/umount /mnt

# Set a flag in case the raid status file is not found
#
RAIDOWN="raidboot.ro not found"
RAIDREF="raidgood.ref not found"
echo "Reading md0 shutdown status."

# search for raid shutdown status
for Device in ${RaidBootDevs}
do
#   these filesystem types should be in 'fstab' since
#   the partitions must be mounted for a clean raid shutdown
    /bin/mount ${Device} /mnt
    if [ -f /mnt/${RaidStatusPath}/raidboot.ro ]; then
	RAIDOWN=`/bin/cat /mnt/${RaidStatusPath}/raidboot.ro`
	RAIDREF=`/bin/cat /mnt/${RaidStatusPath}/raidgood.ref`
	/bin/umount /mnt
	break
    fi
    /bin/umount /mnt
done
# Test for a clean shutdown with array matching reference
if [ "${RAIDOWN}" != "${RAIDREF}" ]; then
    Warning shutdown ERROR ${RAIDOWN}
    FaultExit
fi

# The raid array is clean, remove shutdown status files
for Device in ${RaidBootDevs}
do
    /bin/mount ${Device} /mnt
    /bin/rm -f /mnt/${RaidStatusPath}/raidboot.ro
    /bin/umount /mnt
done

# Write a clean superblock on all raid devices

echo "write clean superblocks"
/sbin/mkraid -f --only-superblock /etc/${RaidConfigEtc}

# Activate raid array(s)
if [ -z "$Raid_ALT" ]; then
    /sbin/mdadd -ar
else
    /sbin/mdadd $Raid_ALT
fi

#  If there are errors - BAIL OUT and leave rescue running
if [ $? -ne 0 ]; then
   Warning some RAID device has errors
   FaultExit
fi

# Everything is fine, let the kernel mount /dev/md0
# tell the kernel to switch to /dev/md0 as the /root device
# The 0x900 value is the device number calculated by:
#  256*major_device_number + minor_device number
echo "/dev/md0 mounted on root"
echo 0x900>/proc/sys/kernel/real-root-dev
# umount /proc to deallocate initrd device ram space
/bin/umount /proc
exit
#------------------ end linuxrc ----------------------
</verb>
<!--
Add 'linuxrc' to initrd boot device
-->
`linuxrc' を initrd の起動デバイスに追加します．
<verb>
	cd /root/raidboot
	chmod 777 linuxrc
	cp -p linuxrc mnt
</verb>

<sect1> シャットダウン用の rc スクリプトの修正 <label id="modify_shutdown">
<!--
Modifying the rc-scripts for SHUTDOWN <label id="modify_shutdown">
-->

<p>
<!--
To complete the installation, modify the rc scripts to save
the md status to the real root device when shutdown occurs.
-->
インストールの最後の手順は，シャットダウン時に md の状態を本当のルート
デバイスに保存するさせるように rc スクリプトを修正することです．
<!--
In slackware this is rc.0 - &mt; rc.6
In debian 'bo' this is in both 'halt' and 'reboot'
-->
<verb>
Slackware の場合は，rc.0 から rc.6 です．Debian `bo' の場合は，これは 
`halt' 及び `reboot' になります．
</verb>
<!--
If you implement this in another distribution, please e-mail
the instructions and sample files so they can be included here.
-->
<verb>
もしこれ以外のディストリビューションで実行した場合は，この文書に追加す
るため，手順とサンプルファイルを筆者にメールで送ってください．
</verb>
<!--
I have modified Bohumil Chalupa's raid stop work-around slightly. His
original solution is presented in <ref id="Appendix-A" name="Appendix A">.
-->
私はRAID 停止時の問題回避のための  Bohumil Chalupa さんの方法を少し変
更したものを使っています．彼の示した元の方法は
<ref id="Appendix-A" name="付録A">で述べます．
<p>
<!--
Since there are no linux partitions left on the production system except
<bf/md0/, the boot partitions are used to store the <bf/raidOK readonly/ status.
I chose to write a file to each of the duplicate boot partitions containing the
status of the md array at shutdown and signifying that the
md device has been remounted RO. This allows the system to be fail safe 
when any of the hard drives die.
-->
私の仕事用システムには <bf/md0/ 以外の Linux パーティションは残ってい
ないので，<bf/raidOK readonly/ のステータスを保存するために起動パーティ
ションを使っています．筆者はシャットダウン時に md アレイのステータスを
含む起動パーティションとその複製の両方へファイルを書き込み，md デバイ
スがリードオンリーで再マウントされたことを記録することにしました．これ
はハードディスクのどれかが壊れたときの障害対策となります．
<p>
<!--
The shutdown script is modified to call <ref id="Appendix-F"
name="rc.raidown"> which saves the necessary
information to successfully reboot and mount the raid device. Examples of 
shutdown scripts for various linux distributions are shown in
<ref id="Appendix-B" name="Appendix B">.
-->
シャットダウンスクリプトは修正され，<ref id="Appendix-F"
name="rc.raidown"> という名前になります．これは，正しく再起動して，
RAID デバイスをマウントするために必要な情報を保存するためのものです．
各ディストリビューション用のシャットダウンスクリプトの例は <ref
id="Appendix-B" name="付録 B">で紹介します．

<p>
<!--
To capture the raid array shutdown status insert a call to
<ref id="Appendix-F" name="rc.raidown">
after any <bf/case/ statements (if present) but before the actual shutdown
(kills, status saves, etc...) begins and before the file systems are 
dismounted.
-->
RAID アレイのシャットダウン時ののステータスを得るために，全ての 
<bf/case/ 文(もしあれば)の後で，かつ，実際のシャットダウン(kill, 状態
保存等)とファイルシステムのアンマウントの前の部分において <ref
id="Appendix-F"name="rc.raidown">を呼び出します．
<verb>
############ Save raid boot and status info ##############
#
  if [ -x /etc/rc.d/rc.raidown ]; then
    /etc/rc.d/rc.raidown
  fi
################## end raid boot #########################
</verb>
<!--
After all the file systems are dismounted (the root file system
'will not' dismount) but before any powerfail status check add:
-->
全てのファイルシステムがアンマウントされた後(ルートファイルシステムは
アンマウント「されません」)かつ，電源断のステータスチェックの前に次の
コマンドを入れます．
<verb>
################ for raid arrays #########################
# Stop all known raid arrays (except root which won't stop)
  if [ -x /sbin/mdstop ]; then
    echo "Stopping raid"
    /sbin/mdstop -a
  fi
##########################################################
</verb>
<!--
This will cleanly stop all raid devices except root.  Root status
is passed to the next boot in <bf/raidstat.ro/.
-->
これによりルート以外の全ての RAID デバイスを安全に停止させることができ
ます．ルートのステータスは <bf/raidstat.ro/ に記録され，次回の起動時に
参照されます．

<p>
<!--
Copy the rc file to your new raid array, the rescue file system that is
still mounted on <bf>/root/raidboot/mnt</bf> and the development system 
if it is on the same machine. 
-->
rc ファイルを新しい RAID アレイ，まだ  <bf>/root/raidboot/mnt</bf> に
マウントされている復旧ファイルシステム，(もし同じマシンならば)
作業用システムのそれぞれにコピーします．

<!--
Modify rescue <bf>etc/fstab</bf> as needed
and make sure rescue <bf/mdtab/ is correct.
-->
必要に応じて復旧ファイルシステムの<bf>etc/fstab</bf>の修正と，復旧ファ
イルシステムの <bf/mdtab/ が正しいかどうかのチェックを行います．
<p>
<!--
Now copy the rescue disk to your dos partition and everything should
be ready to boot the raid device as root.
-->
さて，復旧ディスクを DOS パーティションにコピーすれば，RAID デバイスを 
ルートファイルシステムとしてシステムを起動する準備は終わりです．
<verb>
	umount mnt
	losetup -d /dev/loop0
	gzip -9 rescue
</verb>
<!--
Copy rescue.gz to your boot partitions.
-->
起動パーティションに rescue.gz をコピーします．
<p>
<!--
All that remains is to creat the configuration file <bf/raidboot.conf/
and test the new file system  by rebooting.
-->
残る作業は，設定ファイル <bf/raidboot.conf/ を作り，システムを再起動し
て新しいファイルシステムをテストすることだけです．

<sect1>Configuring RAIDBOOT - raidboot.conf <label id="raidboot-conf">
<p>
<!--
The comments following the example configuration file explain each of the
three lines. This example file is for a 4 drive raid5 scsii array with 
duplicate boot partitions on drives sda1 and sdb1. Put the paramaters
descriptive of your file systems here instead.
-->
設定例の後のコメントは，設定ファイルの最初の3行のそれぞれについての説
明です．例は 4 ドライブの SCSI RAID5 アレイで，起動パーティションを 
sda1 と sdb1 ドライブに複製している場合のものです．実際に使用する場合
には，この代わりにファイルシステムに応じたパラメータを設定してください．
<!--
<verb>
  /dev/sda1 /dev/sdb1
  linux
  raid5.conf
# comments may only be placed 'after' the three
# configuration lines.
#
# This is 'raidboot.conf'
#
# line one, the partition(s) containing the 'initrd' raid-rescue system
#       It is not necessary to boot from these partitions, however,
#       since the rescue system will not fit on floppy, it is necessary
#       to know which partitions are to be used to load the rescue system
#
# line two, the path to the raidboot config information
#       Where the shutdown status, etc... is located at boot time
#       It does NOT include the mount point information, only 'path'
#       /mntpoint/'path'
#
# line -3-, name of the raid configuration file
#       Current raid configuration file i.e. raid1.conf, raid5.conf
</verb>
-->
<verb>
  /dev/sda1 /dev/sdb1
  linux
  raid5.conf
# コメントは3つの設定行の「後」にのみ記述することができます．
#
# このファイルは 'raidboot.conf' です．
#
# 1行目, 'initrd' RAID-復旧システムのあるパーティション
#       これらのパーティションから起動する必要はありませんが，復旧シス
#       テムはフロッピーディスクには入らないでしょうから，復旧システム
#       をどのパーティションからロードするのかわからなければなりません．
#
# 2行目, raidboot の設定情報へのパス
#       シャットダウン時のステータス等が起動時にどこにあるのか示します．
#       これはマウントポイントの情報は含まず，'パス'
#       /マウントポイント/'パス'のみを含みます．
#
# 3行目, RAID 設定ファイルのファイル名
#       現在の RAID 設定ファイルですから，つまり raid1.conf,
#       raid5.conf になります．
</verb>

<sect1>復旧，RAID システムの 'loadlin と LILO' のカーネルパラメータ指定
<!-- Kernel 'loadlin and lilo' variables for RESCUE and RAID -->

<p>
<!--
There are two kernel variables for the RESCUE and RAID system, only the first need
be specified.
-->
復旧とRAIDの2つのカーネルパラメータがありますが，指定する必要があるの
は前者のみです．
<itemize>
<item>Raid_Conf=msdos,/dev/sda1,raidboot
<quote><!-- This variable points to raid boot device and configuration file.
For floppy rescue boot, you may want to specify 
this on the kernel command line or in the loadlin or lilo boot file
-->
このパラメータは RAID 起動デバイスと設定ファイルを指定します．フロッピー
ディスクの復旧システムを起動する場合には，カーネルのコマンドライン，
loadlin あるいは LILO の起動ファイルにこの記述をします．
</quote><quote>
<!--
format: <tt/'filesystem-type,device,path-to-config-from-mountpoint'/
-->
書式: <tt/'ファイルシステムの種類,デバイス,マウントポイントから設定ファイルへのパス'/
</quote>
<item>Raid_ALT=-r,-p5,/dev/md0,/dev/sda3 /dev/sdb3 /dev/sdc3 /dev/sdd3
<quote><!-- Alternate mdadd parameters
necessary when booting with non-redundant raid array. These are the comma
separated command line parameters for <bf/mdadd/. Unless they are needed to
start a failed/non-redundant array, COMMENT OUT OR SPECIFY WITH A 'NULL'.
-->
mdadd のパラメータの代わりになります．冗長でない RAID アレイから起動す
るときに必要となります．<bf/mdadd/ のコマンドラインパラメータをコンマ
区切りで記述します．破損した/非冗長アレイを動かす必要があるとき以外に
は，コメントアウトするか'ヌル文字列'を指定します．
</quote><quote><!-- i.e. Raid_ALT= -->すなわち Raid_ALT= を指定します．
</quote></itemize>
<!--
Either of these parameters may be specified in the lilo or loadlin boot parameter
file or on the loadlin kernel command line. Care must be taken that the maximum 
line length is not exceeded, however, if the command line is used 
(128 characters).
-->
いずれのパラメータも LILO や loadlin の起動パラメータファイルか，
loadlin のカーネルコマンドラインで指定できます．しかし，コマンドライン
で指定する場合には，行の最大の長さ(128文字)を越えないように注意してく
ださい．
<p>
<!--
When booting with <bf/lilo/, the parameters are included in the lilo config
file in the form:
-->
<bf/LILO/ で起動する場合には，LILO の設定ファイルへの記述は次のように
なります．
<verb>
append="Raid_Conf=msdos,/dev/sda1,raidboot"
append="Raid_ALT=-r,-p5,/dev/md0,/dev/sda3 /dev/sdb3 /dev/sdc3 /dev/sdd3"
</verb>
<!--
See <bf/man lilo.conf/ for more detailed information.
-->
より詳しくは<bf/man lilo.conf/を参照してください．
<p>
<!--
Since I have some hardware that requires DOS configuration utilities, I
have a small dos partition on the system.
Therefore, I used loadlin to boot the raid5 system from the dos
partition with a mirror (copy) on the companion disk. An identical method is
used for the raid1 system. The example below uses loadlin, but the procedure
is very similar for lilo.
-->
筆者は DOS の設定ユーティリティを必要とするハードウェアを持っているの
で，システムに小さな DOS パーティションを作っています．したがって，
対になるディスク上にミラー(コピー)を持つ RAID5 システムを起動するのに 
loadlin を使っています．同じ方法を RAID1 システムでも使っています．以
下の例では loadlin を使っていますが，やり方は LILO とよく似ています．
<p>
<!--
My dos root system contains a small editor among the utilities so I can modify
the boot parameters of loadlin if necessary, allowing me to reboot the
linux system on my swap disk while testing.
-->
必要に応じて loadlin の起動パラメータを編集したり，テスト中にスワップ
ディスク上で Linux システムを起動できるように，DOS にルートを持つシス
テムには小さいエディタを入れています．
<p>
<!--
The dos system contains this tree for linux"
-->
DOS システムには Linux のために以下のようなファイルを持っています．
<verb>
	c:\raidboot.bat
	c:\raidboot\loadlin.exe
	c:\raidboot\zimage
	c:\raidboot\rescue.gz
	c:\raidboot\raidboot.cfg
	c:\raidboot\raidboot.etc
	c:\raidboot\raidgood.ref
	c:\raidboot\raidstat.ro	(only at shutdown)

</verb><label id="linuxbat"><!-- linux.bat contains: -->linux.bat の内容は以下です．
<verb>
---------------------- linux.bat ---------------------------
echo "Start the LOADLIN process:"
c:\raidboot\loadlin @c:\raidboot\boot.par
-------------------- end linux.bat -------------------------
</verb>
<!-- boot.par contains: -->
boot.par の内容は以下です．
<verb>
	# loadlin boot parameter file
	#
	# version 1.02 3-6-98

	# linux kernel image
	c:\linux\zimage

	# target root device
	root=/dev/md0
	#root=/dev/ram0
	#root=/dev/sdc5

	# mount root device as 'ro'
	ro

	# size of ram disk
	ramdisk_size=16384

	# initrd file name
	initrd=c:\raidboot\rescue.gz
	#noinitrd

	# memory ends here
	mem=131072k

	# points to raid boot device, configuration file
	# for floppy rescue boot, you may want to specify 
	# this on the command line instead of here
	# format 'filesystem-type,device,path-to-config-frm_mntpnt'
	Raid_Conf=msdos,/dev/sda1,raidboot

	# Alternate mdadd parameters
	# necessary when boot with non-redundant raid
	# otherwise, COMMENT OUT OR SPECIFY 'NULL'
	#Raid_ALT=-r,-p5,/dev/md0,/dev/sda3 /dev/sdb3 /dev/sdc3 /dev/sdd3

	# ethernet devices
	ether=10,0x300,eth0
</verb>
<!--
***** >> NOTE!! the only difference between forcing the rescue system to
	    run and the raid device mounting, is the loadlin parameter

		root=/dev/ram0		for the rescue system
		root=/dev/md0		for RAID

		With root=/dev/ram0 the RAID device will not mount
		and the rescue system will run unconditionally.
-->
<verb>
***** >> 注意!! 復旧システムの起動と，RAID デバイスのマウントの場合で
            は，loadlin のパラメータが

		root=/dev/ram0		for the rescue system
		root=/dev/md0		for RAID

            のように異なるだけです．root=/dev/ram0 を指定すると，RAID 
	    デバイスはマウントされず，必ず復旧システムが起動されます．
</verb>
<!--
If the RAID array fails, the rescue system is left mounted and running.
-->
RAID アレイの認識に失敗すると，復旧システムはマウントされ，動作します．

<sect>筆者の仕事用 RAID システムの設定
<!-- Configuring the Production RAID system. -->

<p>
<sect1>システムの仕様
<!-- System specs. -->
<!--
Two systems with identical motherboards were configured.
-->
同じマザーボードが入っている2つのシステムの設定を以下に示します．
<p>
<!--
<verb>
				  Raid-1	  Raid-5
Motherboard:	Iwill P55TU	dual ide	adaptec scsi
Processor:	Intel P200
Disks:				2ea  7 gig 	4 ea Segate 4.2 gig
				Maxtors		wide scsii
</verb>
-->
<verb>
				  Raid-1	  Raid-5
マザーボード:	Iwill P55TU	IDE * 2		Adaptec SCSI
プロセッサ:	Intel P200
ディスク:			7G * 2 	 	Segate 4.2G * 4
				Maxtors		Wide SCSI
</verb>
<!--
The disk drives are designated by linux as 'sda' through 'sdd' on the raid5
system and 'hda' and 'hdc' on the raid1 system.
-->
ディスクドライブは RAID5 のマシンでは 'sda' から 'sdd' と認識され，
RAID1 のシステムでは 'hda', 'hdc' と認識されています．

<sect1>ハードディスクのパーティション分割
<!-- Partitioning the hard drives. -->

<p>
<!--
Since testing a large root mountable RAID array is difficult because
of the ckraid re-boot problem, I re-partitioned my swap space to include a 
smaller RAID partition for testing purposes, sda6,sdb6,sdc6,sdd6, and
a small root and /usr/src partition pair for developing and testing
the raid kernel and tools.
You may find this helpful.
-->
再起動時の ckraid の問題があるため，ルートにマウント可能な RAID アレイ
をテストすることは大変なので，筆者はスワップパーティションを切り直し，
テスト用の小さい RAID パーティション(sda6,sdb6,sdc6,sdd6)をここに作り，
小さいルートパーティションと /usr/src パーティションの組を RAID 用カー
ネルとツールの作業用とテスト用にそれぞれ作りました．
これは便利な方法だと思います．

<verb>
	<bf/作業用システム - RAID5/
   デバイス 	システム	サイズ	目的

  /dev/sda1     DOS 起動        16M     起動パーティション
* /dev/sda2     extended        130M    (説明参照)
  /dev/sda3     linux native    4G      プライマリ RAID5-1
----------------------sda2------------------------------
* /dev/sda5     linux swap      113M    スワップ
* /dev/sda6     linux native    16M     テスト RAID5-1
========================================================
  /dev/sdb1     dos boot        16M     起動パーティション複製
* /dev/sdb2     extended        130M    (説明参照)
  /dev/sdb3     linux native    4G      プライマリ RAID5-2
----------------------sdb2------------------------------
* /dev/sdb5     linux swap      113M    スワップ
* /dev/sdb6     linux native    16M     テスト RAID5-2
========================================================
* /dev/sdc2     extended        146M    (説明参照)
  /dev/sdc3     linux native    4G      プライマリ RAID5-3
----------------------sdc2------------------------------
* /dev/sdc5     linux swap      130M    作業用ルートパーティション
* /dev/sdc6     linux native    16M     テスト RAID5-3
========================================================
* /dev/sdd2     extended        146M    (説明参照)
  /dev/sdd3     linux native    4G      プライマリ RAID5-4
----------------------sdd2------------------------------
* /dev/sdd5     linux swap      130M    作業用 /usr/src
* /dev/sdd6     linux native    16M     テスト RAID-4


	<bf/作業用システム - RAID1/
   デバイス 	システム	サイズ	目的

  /dev/hda1	DOS 		16M	起動パーティション
* /dev/hda2	extended	126M	(説明参照)
  /dev/hda3	linux		126M	作業用ルートパーティション
  /dev/hda4	linux		6+G	RAID1-1
----------------------hda2------------------------------
* /dev/hda5	linux		 26M	テスト RAID1-1
* /dev/hda6	linux swap	100M
========================================================

  /dev/hdc1	hda1 の単なるコピー．したがって，hda が故障
                した場合にはアクティブにすることができる
* /dev/hdc2	extended	126M	(説明参照)
  /dev/hdc3	linux		126M	作業用 /usr/src
  /dev/hdc4	linux		6+G	RAID1-2
----------------------hdc2------------------------------
* /dev/hdc5	linux		 26M	テスト RAID1-2
* /dev/hdc6	linux swap	100M
</verb>

<!--
The sdx2 and hdx3 partitions were switched to 'swap' after developing
this utility. I could have done it on another machine, however,
the libraries and kernels are all about a year or more out of date
on my other linux boxes and I preferred to build it on the target machine.
-->
sdx2 と hdx3 パーティションは，ユーティリティの開発が終わった後には，
'スワップ'にすることができます．筆者も別のマシンでこれをすることができ
たのですが，他の Linux マシンのライブラリやカーネルが1年以上古いものだっ
たので，ターゲットマシンで作ることにしました．
<p>
<!--
The partitioning scheme was chosen so that in the event that 
any one of the drives fails catastrophically, the system will
continue to run and be bootable with minimum effort and NO data loss.
-->
パーティションの切り方は，ディスクのどれかが壊れてしまった場合にも，シ
ステムができるだけ簡単に起動し続けるようにでき，データも失わないように
決めました．
<!--
<itemize>
<item>	If any single hard drive fails, the boot will abort, and
	the rescue system will run. Examination of the screen
	message or /dos<it/x//raidboot/raidstat.ro will tell the operator
	the status of the failed array.
<item>	If sda1 (raid5) or hda1 (raid1) fails, the dos backup boot partition 
	must be made 'active' and the bios must recognize the new partition 
	as the boot device or it must be physically be moved to the <it/x/da position. 
	Alternatively, the system could be booted from a floppy disk using
	the initrd image on the remaining backup boot drive.
	The raid system can then be made active again by issuing:
<verb>	 "/sbin/mkraid /etc/raid<it/x/.conf -f only-superblock"</verb>
	to rebuild the remaining superblock(s).

<item>	Once this is done, then 

<verb>	mdadd -ar</verb>

<item>	Examine the status of the array to verify that everything is OK
	then replace the good array reference with the current status
	until the failed disk can be repaired or replaced.

<verb>	cat /proc/mdstat | grep md0 > /dosx/raidboot/raidgood.ref

	shutdown -r now
</verb>
	to do a clean reboot, and the system is up again.
</itemize>
-->
<itemize>
<item>  1つのハードディスクが壊れた場合，起動は失敗し，復旧システムが
        稼働します．画面上のメッセージか，
        /dos<it/x//raidboot/raidstat.ro を調べれば，壊れたアレイのステー
        タスを知ることができます．
<item>  sda1(RAID5) か hda1(RAID1) が故障した場合，DOS のバックアップ
        起動パーティションを「アクティブ」にし，BIOS に 新しいパーティ
        ションを起動デバイスとして認識させるか，あるいは，物理的に
        <it/x/da パーティションを移動させなければなりません．
        その代わりに，initrd イメージを使ってフロッピーディスクから残っ
        ているバックアップ起動ドライブ上のシステムを起動することもでき
        ます．その後，残っているスーパーブロックを再構築するため，次の
        コマンドを実行することで RAID システムを再びアク
        ティブにすることができます．
<verb>	 "/sbin/mkraid /etc/raid<it/x/.conf -f --only-superblock"</verb>

<item>	これを行った後，

<verb>	mdadd -ar</verb>

        を実行します．

<item>  問題がないことを検査するため，アレイのステータスを調べ，それか
        ら，壊れたディスクが修理されるか交換されるまで，正常なアレイの
        参照ステータスを現在のステータスで置き換えます．

<verb>	cat /proc/mdstat | grep md0 > /dosx/raidboot/raidgood.ref

	shutdown -r now
</verb>
	によって正常な再起動を行い，システムを復旧させます．
</itemize>

<sect>RAID ファイルシステムの構築
<!-- Building the RAID file system. -->

<p>
<!--
This description is for my RAID systems described in the system
specs.  Your system may have a different RAID architecture, so
modify as appropriate. Please read the man pages and 
QuickStart.RAID that come with the raidtools-0.42
-->
この記述は，システム仕様で述べた筆者の RAID1 システムに関してのもので
す．あなたのシステムが異なる RAID のアーキテクチャを採用している場合は，
適宜修正してください．詳しくは raidtools-0.42 に付属しているオンライン
マニュアルか，QuickStart.RAID を参照してください．
<sect1>/etc/raid5.conf <label id="raid5configuration">
<p>
<verb>	# raid-5 configuration
	raiddev                 /dev/md0
	raid-level              5
	nr-raid-disks           4
	chunk-size              32

	# Parity placement algorithm
	parity-algorithm        left-symmetric

	# Spare disks for hot reconstruction
	#nr-spare-disks         0

	device                  /dev/sda3
	raid-disk               0

	device                  /dev/sdb3
	raid-disk               1

	device                  /dev/sdc3
	raid-disk               2

	device                  /dev/sdd3
	raid-disk               3
</verb>
<sect1>/etc/raid1.conf <label id="raid1configuration">
<p>
<verb>
        # raid-1 configuration
        raiddev                 /dev/md0
        raid-level              1
        nr-raid-disks           2
        nr-spare-disks          0

        device                  /dev/hda4
        raid-disk               0

        device                  /dev/hdc4
        raid-disk               1
</verb>
<sect1>仕事用 RAID ファイルシステムを構築するための具体的手順
<!--Step by Step procedures for building production RAID file system. -->
<p>
<!--
For my RAID5 system I did a complete install of:
-->
筆者の RAID5 システムでは，以下のものをインストールしています．
<!--
<verb>
	Slackware-3.4		any current distribution should work OK
	linuxthreads-0.71
	raidtools-0.42
	linux-2.0.33 with raid145 patch and Gadi's patch
</verb>
-->
<verb>
	Slackware-3.4		どのディストリビューションでも大丈夫でしょう
	linuxthreads-0.71
	raidtools-0.42
	linux-2.0.33 に raid145 パッチと Gadi 氏のパッチを当てたもの
</verb>

<p>
<!--
Create and format the raid device.
-->
RAID デバイスを作成，フォーマットします．
<verb>
	mkraid /etc/raid5.conf
	mdcreate raid5 /dev/md0 /dev/sda3 /dev/sdb3 /dev/sdc3 /dev/sdd3
	mdadd -ar
	mke2fs /dev/md0
	mkdir /md
	mount -t ext2 /dev/md0 /md
</verb>
<!--
Create the reference files that reboot will use,
this may be different on your system.
-->
reboot が使う参照ファイルを作成します．これは読者のシステムでは異なる
かもしれません．
<verb>
	cat /proc/mdstat | grep md0 > /dosa/raidboot/raidgood.ref
        cat /proc/mdstat | grep md0 > /dosb/raidboot/raidgood.ref
</verb>
<!--
Use Slackware-3.4 or another distribution to build your OS
-->
Slackware-3.4 または別のパッケージを用いて，OS をインストールします．
<verb>
	setup
</verb>
<!--
Specify '/md' as the target, and the source whatever your normally use.
Select and install the disksets of interest except for the kernel.
Configure the system, but skip the section on lilo and kernel booting.
Exit setup.
-->
インストール先には `/md' を，インストール元には読者が普段使っているも
のを指定します．カーネルを除く必要なディスクセットを選択，インストール
します．(Slackware の場合)システム設定(Configure)を実行しますが，lilo 
とカーネルの起動の項目は飛ばします．最後に setup コマンドを終了します．
<p>
<!--
Install 'pthreads'
-->
`pthreads' をインストールします．
<verb>
	cd /usr/src/linuxthreads-0.71
</verb>
<!--
edit the Makefile and specify
-->
Makefile を編集し，環境変数を指定します．
<verb>
	BUILDIR=/md

	make
	make install
</verb>
<!--
Install 'raidtools'
-->
`raidtools' をインストールします．
<verb>
	cd /usr/src/raidtools-0.42
	configure --sbindir=/md/sbin --prefix=/md/usr
</verb>
<!--
fix the raidtools make install error
-->
raidtools の `make install' で発生するエラーを修正します．
<verb>
	cd /md/sbin
	rm mdrun
	rm mdstop
	ln -s mdadd mdrun
	ln -s mdadd mdstop
</verb>
<!--
Create /dev/mdx
-->
/dev/mdx を作ります．
<verb>
	cp -a /dev/md* /md/dev
</verb>
<!--
Add the system configuration from the current system (ignore errors).
-->
現在のシステムからシステム設定を追加します(エラーは無視します)．
<!--
<verb>
	cp -dp /etc/* mnt/etc
	cp -dp /etc/rc.d/* mnt/etc/rc.d		(include the new rc.6)
	mkdir  mnt/lib/modules
	cp -a  /lib/modules/2.x.x mnt/lib/modules  your current 2.x.x
</verb>
-->
<verb>
	cp -dp /etc/* mnt/etc
	cp -dp /etc/rc.d/* mnt/etc/rc.d		(新しい rc.6 を含む)
	mkdir  mnt/lib/modules
	cp -a  /lib/modules/2.x.x mnt/lib/modules &lt;&mdash; 現在使っているカーネル 2.x.x のバージョン
</verb>
<!--
Edit the following files to correct them for your file system
-->
以下のファイルを編集し，読者のファイルシステムに合わせて修正します．
<!--
<verb>
	cd /md

Non-network
	etc/fstab	correct for real root and raid devices.
	etc/mdtab	should work OK
Network
	etc/hosts
	etc/resolv.conf	
	etc/hosts.equiv		and related files
	etc/rc.d/rc.inet1	correct ip#, mask, gateway, etc...
	etc/rc.d/rc.S		remove entire section on file system status
		from:
			# Test to see if the root partition isread-only
		to but not including:
			# remove /etc/mtab* so that mount will .....
				This avoids the annoying warning that
				the ramdisk is mounted rw.
	etc/rc.d/rc.xxxxx	others as required
	root/.rhosts		if present
	home/xxxx/xxxx		others as required

    WARNING:	The above procedure moves your password and shadow
		files onto the new file system!!!!!

    WARNING:	You may not wish to do this for security reasons.
</verb>
-->
<verb>
	cd /md

非ネットワーク関係
	etc/fstab	実際のルートファイルシステムと RAID デバイス用に修正します
	etc/mdtab	うまく動作するはずです
ネットワーク関係
	etc/hosts
	etc/resolv.conf	
	etc/hosts.equiv		及び関連ファイル
	etc/rc.d/rc.inet1	IP アドレス，ネットマスク，ゲートウェイ等
	etc/rc.d/rc.S		ファイルシステムのステータスについての部分を全て削除
			# Test to see if the root partition isread-only
                の部分から
			# remove /etc/mtab* so that mount will .....
                までを含まないようにします．これにより，RAM ディスクが
                読み書き可能でマウントされると出るうるさいウォーニング
                が出なくなります．
	etc/rc.d/rc.xxxxx	必要ならば他のファイルも
	root/.rhosts		もし存在すれば
	home/xxxx/xxxx		必要ならば他のファイルも

    警告:	この操作で，パスワードとシャドウパスワードのファイルも
		新しいファイルシステムに移されます！これはセキュリティ
		の点からは，望ましくないかもしれません．
</verb>
<!--
Create any directories for mounting /dev/disk... as may be required
that are unique to your system.  Mine need:
-->
システム上で一意であることが必要な /dev/disk... をマウントするための辞
書を作成します．筆者の場合は以下のようになりました．
<!--
<verb>
	cd /md		< - new file system root
	mkdir dosa			dos partition mount point
	mkdir dosb			dos mirror mount point
</verb>
-->
<verb>
	cd /md		&lt;&mdash; 新しいファイルシステムのルート
	mkdir dosa			DOSパーティションのマウントポイント

	mkdir dosb			DOS ミラーパーティションのマウントポイント
</verb>
<!--
The new file system is complete. Make sure and save the md reference
status to the 'real' root device and you are ready to boot.
-->
新しいファイルシステムは完成です．md の参照ステータスを `実際の'ルート
デバイスに確認・保存すれば，起動の準備は終わりです．
<p>
<!--
mount the dos partitions on dosa and dosb
-->
DOS パーティションを dosa, dosb にマウントします．
<verb>
	cat /proc/mdstat | grep md0 > /dosa/raidboot/raidgood.ref
	cat /proc/mdstat | grep md0 > /dosb/raidboot/raidgood.ref

	mdstop /dev/md0
</verb>
	
<sect>最後に注意する点
<!-- One last thought. -->

<p>
<!--
Remember that an expert is someone who knows at least 1% more 
than you do about a subject.  Bear this in mind when you e-mail 
me for help.  I'll try, but I've only done this once for raid1 and once for
raid5!
-->
達人とは，ある話題についてあなたより少なくとも1%多くのことを知っている
人のことであることを忘れないでください．私に助けを求めるメールを出すと
きにはこの点を忘れないでください．私は実験をしましたが，それは RAID1,
RAID5 についてたった一度ずつだけなのです！

Michael Robinton <url url="mailto:michael@bzs.org"
name="Michael@bzs.org">

<sect>付録 A. Bohumil Chalupa さんによる md0 のシャットダウン<label
id="Appendix-A">
<!--
Appendix A. - Bohumil Chalupa's md0 shutdown<label id="Appendix-A">
-->

<p>
<!--
Bohumil Chalupa's post to the linux raid list on the work 
around for the raid1 + 5 mdstop problem. His solution does not 
address the possibility of the raid device being corrupt at shutdown.
So I have added a simple status comparison to a good reference
status at boot.  This allows the operator to intervene if something
is wrong with a disk in the array. The description of this is in the
main body of this document.
-->
Bohumil Chalupa さんの Linux RAID メーリングリストへの投稿で，RAID1, 5 
での mdstop の問題の回避方法です．この方法では，シャットダウンの時に 
RAID デバイスが壊れている可能性は想定していません．そこで，筆者がブー
ト時の正常な参照ステータスを簡単に比較するようにしました．これにより，
アレイに異常があるとき，オペレータが調整することができます．これについ
ての詳細は本文中で述べています．

<!--
> From: Bohumil Chalupa <bochal@apollo.karlov.mff.cuni.cz>
>  
> I can now boot initrd and use linuxrc to start the RAID1 array,
> then successfully switch root to /dev/md0.
> 
> I don't know, however, any way how to cleanly _stop_ the array.
-->
<verb>
> From: Bohumil Chalupa <bochal@apollo.karlov.mff.cuni.cz>
>  
> initrd と linuxrc を使ってRAID1 アレイを動かし，それから root を 
> /dev/md0 にうまく切替えることできました．
> 
> しかし，アレイを正常に *止める* 方法はわかりません．
</verb>

<!--
Well. I have to answer myself :-)
-->
<verb>
それでは，私がお答えしましょう :-)
</verb>

<!-- 
> Date: Mon, 29 Dec 1997 02:21:38 -0600 (CST)
> From: Edward Welbon <welbon@bga.com>
> Subject: Re: dismounting root raid device
> 
> For md devices other than raid0, there is probably state that needs to
> be saved that is only known once all writes have completed.  Such state
> of course can't be saved to root once it is mounted readonly.  In that
> case, you would have to be able to mount a writeable filesystem "X"
> on the readonly root and be able to write to "X" (I recall doing this
> during "rescue" operations, but not as an automated procedure).
> 
> The filesystem "X" would presumably be a boot device from which the raid
> (during linuxrc exection via initrd) would pickup it's initial state from.
> Fortunately raid0 isn't required to write out any state (though it would
> be pleasant to be able to write the check sums to mdtab after an mdstop).
> Eventually, I will fiddle with this but it doesn't seem difficult though
> the "devil" is always in the "details".
-->
<verb>
> Date: Mon, 29 Dec 1997 02:21:38 -0600 (CST)
> From: Edward Welbon <welbon@bga.com>
> Subject: Re: dismounting root raid device
> 
> RAID0 以外の md デバイスについては，全ての書き込みが終了していること
> を知るためにステータスを保存すると思います．もちろん，このようなステー
> タスはリードオンリーでマウントされるルートファイルシステムについては
> 保存されません．このような場合，リードオンリーのルートファイルシステ
> ムに書き込み可能なファイルシステム "X" をマウント可能で，"X" に書き
> 込みができなくてはなりません("復旧"の操作でもこれを行いますが，こち
> らは自動処理ではありません)．
>
> ファイルシステム "X" は RAID(initrd 経由で linuxrc が実行)が初期ステー
> タスを取得するブートデバイスと仮定します．幸い raid0 はステータス書
> き込みの必要がありません(mdstop の後に mdtab にチェックサムを書き出
> すことができれば嬉しいのですが)．
> とりあえずこれをいじってみますが，"devil" が常に "details" に含まれ
> ますが，難しくはなさそうです．
</verb>

<!--
Yes, that's it.
I had this idea in mind for some time already, but had no time to try it.
Yesterday I did, and it works. 
-->
<verb>
そうですね．
私も同じアイディアを考えていたのですが，試す時間がありませんでした．
それで，昨日やってみたところ，うまく動きました．
</verb>

<!--
With my RAID1 (mirror), I don't save any checksums or raid superblock data.
I only save an information on the "real" boot partition, that the root md
volume was remounted readonly during shutdown. Then, during boot, the
linuxrc script runs mkraid -only-superblock  when it finds this
information; otherwise, it runs ckraid.
This means, that the raid superblock information is not updated during
shutdown; it's updated at the boot time. 
It is not very clean, I'm afraid,  :-(   but it works.
-->
<verb>
うちの RAID1(ミラー)では，チェックサムやRAIDのスーパーブロックのデータ
の保存は行っていません．"実際"のブートパーティションの情報，つまりルー
トに割り当てた md ボリュームがシャットダウン時にリードオンリーで再マウ
ントされたことだけを保存しています．そして，起動時に linuxrc スクリプ
トがこの情報を見つければ mkraid --only-superblock を実行し，これが見つ
からなければ ckraid を実行します．
つまり，RAID のスーパーブロック情報はシャットダウン時には更新されず，
起動時に更新されます．
あまりすっきりした方法でないのですが， :-( 動いてはいます．
</verb>

<!--
I'm using Slackware and initrd.md by Edward Welbon to boot the root raid
device. 
As far as I remember now, the only modified files are
mkdisk and linuxrc, and /etc/rc.d/rc.6 shutdown script.
And lilo.conf, of course.

I'm appending the important parts.

Bohumil Chalupa
-->
<verb>
私はRAIDデバイスをルートにして起動するために Edward Welbon さんの 
initrd.md と Slackware の組合せを使っています．
私の覚えている限りでは，修正したファイルは mkdisk, linuxrc とシャット
ダウン用のスクリプト /etc/rc.d/rc.6 だけです．
もちろん， lilo.conf は修正しました．

重要な部分をメールに添付しておきます．

Bohumil Chalupa

--------------- my.linuxrc follows -----------------
#!/bin/sh
# we need /proc
/bin/mount /proc 
# start up the md0 device. let the /etc/rc.d scripts get the rest of them
# we should do as little as possible here
# ________________________________________
# root raid1 shutdown test &amp; recreation
# /start must be created on the rd image in my.mkdisk
echo "preparing md0: mounting /start"
/bin/mount /dev/sda2 /start -t ext2
echo "reading saved md0 state from /start"
if [ -f /start/root.raid.ok ]; then
 echo "raid ok, modyfying superblock"
 rm /start/root.raid.ok
 /sbin/mkraid /etc/raid1.conf -f --only-superblock
else
 echo "raid not clean, runing ckraid --fix"
 /sbin/ckraid --fix /etc/raid1.conf
fi
echo "unmounting /start"
/bin/umount /start
# _________________________________________
#
echo "adding md0 for root file system"
/sbin/mdadd /dev/md0 /dev/sda1 /dev/sdb1 
echo "starting md0"
/sbin/mdrun -p1 /dev/md0
# tell kernel we want to switch to /dev/md0 as root device, the 0x900 value
# is arrived at via 256*major_device_number + minor_device number.
echo "setting real-root-dev"
/bin/echo 0x900>/proc/sys/kernel/real-root-dev
#  unmount /proc so that the ram disk can be deallocated.
echo "unmounting /proc"
/bin/umount /proc
/bin/echo "We are hopefully ready to mount /dev/md0 (major 9, minor 0) as
root"
exit
--------------- end of my.linuxrc ----------------------------------


----------- extract from /etc/rc.d/rc.6 follows -----------------
  # Turn off swap, then unmount local file systems.
  echo "Turning off swap."
  swapoff -a
  echo "Unmounting local file systems."
  umount -a -tnonfs
  # Don't remount UMSDOS root volumes:
  if [ ! "`mount | head -1 | cut -d ' ' -f 5`" = "umsdos" ]; then
    mount -n -o remount,ro /
  fi

  # Save raid state
  echo "Saving RAID state"
  /bin/mount -n /dev/sda2 /start -t ext2
  touch /start/root.raid.ok
  /bin/umount -n /start

-------------- end of excerpt from rc.6 ------------------------


------------------ part of my.mkdisk follows ----------------------
#
#  now we have the filesystem ready to be populated, we need to 
#  get a few important directories.  I had endless trouble till
#  I created a pristine mtab.  In my case, it is convenient that
#  /etc/mdtab is copied over, this way I can activate md with
#  a simple "/sbin/mdadd -ar" in linuxrc.
#
cp -a $ROOT/etc $MOUNTPNT 2>cp.stderr 1>cp.stdout
rm -rf $MOUNTPNT/etc/mtab
rm -rf $MOUNTPNT/etc/ppp*
rm -rf $MOUNTPNT/etc/termcap
rm -rf $MOUNTPNT/etc/sendmail*
rm -rf $MOUNTPNT/etc/rc.d
rm -rf $MOUNTPNT/etc/dos* 
cp -a $ROOT/sbin $ROOT/dev $ROOT/lib $ROOT/bin $MOUNTPNT 2>>cp.stderr
1>>cp.stdout
# _____________________________________________________________________
#  RAID: will need mkraid and ckraid
cp -a $ROOT/usr/sbin/mkraid $ROOT/usr/sbin/ckraid $MOUNTPNT/sbin
2>>cp.stderr 1>>cp.stdout
# ---------------------------------------------------------------------
#  it seems that init wont come out to play unless it has utmp.   this can
#  probably be pruned back alot.  no telling what the real bug was 8-).
#
mkdir $MOUNTPNT/var $MOUNTPNT/var/log $MOUNTPNT/var/run $MOUNTPNT/initrd
touch $MOUNTPNT/var/run/utmp $MOUNTPNT/etc/mtab
chmod a+r $MOUNTPNT/var/run/utmp $MOUNTPNT/etc/mtab
ln -s /var/run/utmp $MOUNTPNT/var/log/utmp
ln -s /var/log/utmp $MOUNTPNT/etc/utmp
ls -lstrd $MOUNTPNT/etc/utmp $MOUNTPNT/var/log/utmp $MOUNTPNT/var/run/utmp
#
#  since I wanted to change the mount point, I needed this though
#  I suppose that I could have done a "mkdir /proc" in linuxrc.
#
mkdir $MOUNTPNT/proc
chmod 555 $MOUNTPNT/proc
#
#  ------------------------------------------------------
#  we'll mount the real boot device to /start temporarily
#  to check the root raid state saved at shutdown time
#
mkdir $MOUNTPNT/start
#  -------------------------------------------------------
#
#  need linuxrc  (it is, after all, the point of this exercise).
#
if [ -x ./my.linuxrc ]; then
  cp -a ./my.linuxrc $MOUNTPNT/linuxrc
  chmod 777 $MOUNTPNT/linuxrc
else
   ln -s /bin/sh $MOUNTPNT/linuxrc
fi
#
----------------- part of my.mkdisk ends -----------------
</verb>

<sect> シャットダウンスクリプトの例 <label id="Appendix-B">
<!--
Appendix B. - Sample SHUTDOWN scripts <label id="Appendix-B">
-->

<p><itemize>
<item><ref id="Slackware" name="Slackware">
<item><ref id="Debian" name="Debian">
</itemize>

<sect1>Slackware - /etc/rc.d/rc.6 <label id="Slackware">
<p>
<verb>
#! /bin/sh
#
# rc.6		This file is executed by init when it goes into runlevel
#		0 (halt) or runlevel 6 (reboot). It kills all processes,
#		unmounts file systems and then either halts or reboots.
#
# Version:	@(#)/etc/rc.d/rc.6	1.50	1994-01-15
#
# Author:	Miquel van Smoorenburg <miquels@drinkel.nl.mugnet.org>
# Modified by:  Patrick J. Volkerding, <volkerdi@ftp.cdrom.com>
#
# Modified by:	Michael A. Robinton < michael@bizsystems.com >
#		to add call to rc.raidown
  # Set the path.
  PATH=/sbin:/etc:/bin:/usr/bin

  # Set linefeed mode to avoid staircase effect.
  stty onlcr

  echo "Running shutdown script $0:"

  # Find out how we were called.
  case "$0" in
	*0)
		message="The system is halted."
		command="halt"
		;;
	*6)
		message="Rebooting."
		command=reboot
		;;
	*)
		echo "$0: call me as \"rc.0\" or \"rc.6\" please!"
		exit 1
		;;
  esac

############ Save raid boot and status info ##############
#
if [ -x /etc/rc.d/rc.raidown ]; then
   /etc/rc.d/rc.raidown
fi
################## end raid boot #########################

  # Kill all processes.
  # INIT is supposed to handle this entirely now, but this didn't always
  # work correctly without this second pass at killing off the processes.
  # Since INIT already notified the user that processes were being killed,
  # we'll avoid echoing this info this time around.
  if [ "$1" != "fast" ]; then # shutdown did not already kill all processes
    killall5 -15 
    killall5 -9
  fi

  # Try to turn off quota and accounting.
  if [ -x /usr/sbin/quotaoff ]
  then
	echo "Turning off quota."
	/usr/sbin/quotaoff -a
  fi
  if [ -x /sbin/accton ]
  then
	echo "Turning off accounting."
	/sbin/accton
  fi

  # Before unmounting file systems write a reboot or halt record to wtmp.
  $command -w

  # Save localtime
  [ -e /usr/lib/zoneinfo/localtime ] &amp;&amp; cp /usr/lib/zoneinfo/localtime /etc

  # Asynchronously unmount any remote filesystems:
  echo "Unmounting remote filesystems."
  umount -a -tnfs &amp;

  # Turn off swap, then unmount local file systems.
  echo "Turning off swap."
  swapoff -a
  echo "Unmounting local file systems."
  umount -a -tnonfs
  # Don't remount UMSDOS root volumes:
  if [ ! "`mount | head -1 | cut -d ' ' -f 5`" = "umsdos" ]; then
    mount -n -o remount,ro /
  fi

################ for raid arrays #########################
# Stop all known raid arrays (except root which won't stop)
if [ -x /sbin/mdstop ]; then
  echo "Stopping raid"
  /sbin/mdstop -a
fi
##########################################################

  # See if this is a powerfail situation.
  if [ -f /etc/powerstatus ]; then
    echo "Turning off UPS, bye."
    /sbin/powerd -q
    exit 1
  fi

  # Now halt or reboot.
  echo "$message"
  [ ! -f /etc/fastboot ] &amp;&amp; echo "On the next boot fsck will be FORCED."
  $command -f
############### end rc.6 #################################
</verb>

<sect1>Debian bo - /etc/init.d/halt and /etc/init.d/reboot <label id="Debian">
<p>
The modifications shown here for Debian bo halt and reboot files are NOT
TESTED. When you test this, please e-mail me so I can remove this comment.

<sect2>/etc/init.d/halt
<p>
<verb>
#! /bin/sh
#
# halt		The commands in this script are executed as the last
#		step in runlevel 0, ie halt.
#
# Version:      @(#)halt  1.10  26-Apr-1997  miquels@cistron.nl
#

PATH=/sbin:/bin:/usr/sbin:/usr/bin

############ Save raid boot and status info ##############
#
if [ -x /etc/rc.d/rc.raidown ]; then
   /etc/rc.d/rc.raidown
fi
################## end raid boot #########################

# Kill all processes.
echo -n "Sending all processes the TERM signal... "
killall5 -15
echo "done."
sleep 5
echo -n "Sending all processes the KILL signal... "
killall5 -9
echo "done."

# Write a reboot record to /var/log/wtmp.
halt -w

# Save the random seed between reboots.
/etc/init.d/urandom stop

echo -n "Deactivating swap... "
swapoff -a
echo "done."

echo -n "Unmounting file systems... "
umount -a
echo "done."

mount -n -o remount,ro /

################ for raid arrays #########################
# Stop all known raid arrays (except root which won't stop)
if [ -x /sbin/mdstop ]; then
  echo "Stopping raid"
  /sbin/mdstop -a
fi
##########################################################

# See if we need to cut the power.
if [ -x /etc/init.d/ups-monitor ]
then
	/etc/init.d/ups-monitor poweroff
fi

halt -d -f
############# end halt ####################
</verb>
<sect2>/etc/init.d/reboot
<p>
<verb>
#! /bin/sh
#
# reboot	The commands in this script are executed as the last
#		step in runlevel 6, ie reboot.
#
# Version:	@(#)reboot  1.9  02-Feb-1997  miquels@cistron.nl
#

PATH=/sbin:/bin:/usr/sbin:/usr/bin

############ Save raid boot and status info ##############
#
if [ -x /etc/rc.d/rc.raidown ]; then
   /etc/rc.d/rc.raidown
fi
################## end raid boot #########################

# Kill all processes.
echo -n "Sending all processes the TERM signal... "
killall5 -15
echo "done."
sleep 5
echo -n "Sending all processes the KILL signal... "
killall5 -9
echo "done."

# Write a reboot record to /var/log/wtmp.
halt -w

# Save the random seed between reboots.
/etc/init.d/urandom stop

echo -n "Deactivating swap... "
swapoff -a
echo "done."

echo -n "Unmounting file systems... "
umount -a
echo "done."

mount -n -o remount,ro /

################ for raid arrays #########################
# Stop all known raid arrays (except root which won't stop)
if [ -x /sbin/mdstop ]; then
  echo "Stopping raid"
  /sbin/mdstop -a
fi
##########################################################

echo -n "Rebooting... "
reboot -d -f -i
</verb>

<sect>付録 C: その他の設定ファイル
<!-- Appendix C. - other setup files -->

<p>
<sect1>linuxrc <ref id="linuxrc" name="linuxrc file">
<p>
<sect1>loadlin -- linux.bat file - boot.par <ref id="linuxbat" name="linux.bat file - boot.par">
<p>
<sect1>linuxthreads Makefile.diff <ref id="thrdiff"
	name="linuxthreads Makefile.diff">
<p>
<sect1>raid1.conf <ref id="raid1configuration" name="raid1.conf">
<p>
<sect1>raid5.conf <ref id="raid5configuration" name="raid5.conf">
<p>
<sect1>raidboot.conf <ref id="raidboot-conf" name="raidboot.conf">
<p>
<sect1>rc.raidown <ref id="Appendix-F" name="rc.raidown">

<sect>付録 D: 古い linuxrc とシャットダウンスクリプト <label id="Appendix-D">
<!--
Appendix D. - obsolete linuxrc and shutdown scripts <label id="Appendix-D">
-->

<p>
<sect1>古いファイル &ndash; linxurc
<!-- Obsolete working - linuxrc -->
<p>
<!--
This linuxrc file works fine with the shutdown procedure in the next
subsection.
-->
この linuxrc ファイルは次の節で示すシャットダウンスクリプトと組み合わ
せれば正しく動作します．
<verb>
 ---------------------- linuxrc --------------------
#!/bin/sh
# ver 1.07 2-12-98
# linuxrc - for raid1 using small dos partition and loadlin
#

# mount the proc file system
/bin/mount /proc

# This may vary for your system.
# Mount the dos partitions, try both
# in case one disk is dead
/bin/mount /dosa
/bin/mount /dosc

# Set a flag in case the raid status file is not found
# then check both drives for the status file
RAIDOWN="raidstat.ro not found"
/bin/echo "Reading md0 shutdown status."
if [ -f /dosa/raidboot/raidstat.ro ]; then
  RAIDOWN=`/bin/cat /dosa/raidboot/raidstat.ro`
  RAIDREF=`/bin/cat /dosc/raidboot/raidgood.ref`
else
  if [ -f /dosc/raidboot/raidstat.ro ]; then
    RAIDOWN=`/bin/cat /dosc/raidboot/raidstat.ro`
    RAIDREF=`/bin/cat /dosc/raidboot/raidgood.ref`
  fi
fi

# Test for a clean shutdown with all disks operational
if [ "${RAIDOWN} != ${RAIDREF}" ]; then
  echo "ERROR ${RAIDOWN}"
#  Use the next 2 lines to BAIL OUT and leave rescue running
   /bin/echo 0x100>/proc/sys/kernel/real-root-dev
   exit                 # leaving the error files in dosa/raidboot,etc...
fi

# The raid array is clean, proceed by removing
# status file and writing a clean superblock
/bin/rm /dosa/raidboot/raidstat.ro
/bin/rm /dosc/raidboot/raidstat.ro
/sbin/mkraid /etc/raid1.conf -f --only-superblock

/bin/umount /dosa
/bin/umount /dosc

# Mount raid array
echo "Mounting md0, root filesystem"
/sbin/mdadd -ar

#  If there are errors - BAIL OUT and leave rescue running
if [ $? -ne 0 ]; then
   echo "RAID device has errors"
#  Use the next 3 lines to BAIL OUT
   /bin/rm /etc/mtab		# remove bad mtab
   /bin/echo 0x100>/proc/sys/kernel/real-root-dev
   exit
fi

# else tell the kernel to switch to /dev/md0 as the /root device
# The 0x900 value the device number calculated by:
#  256*major_device_number + minor_device number
/bin/echo 0x900>/proc/sys/kernel/real-root-dev

# umount /proc to deallocate initrd device ram space
/bin/umount /proc
/bin/echo "/dev/md0 mounted as root"
exit
#------------------ end linuxrc ----------------------
</verb>

<sect1>古いファイル &ndash; シャットダウンスクリプト
<!-- Obsolete working - shutdown scripts -->
<p>
<!--
This shutdown procedure works fine with the preceeding <bf/linuxrc/
-->
このシャットダウンスクリプトは前に示した <bf/linuxrc/ と組み合わせれば
正しく動作します．
<p>
<!--
To capture the raid array shutdown status,
just before the file systems are dismounted insert:
-->
RAID アレイのシャットダウン時のステータスを得るために，ファイルシステ
ムをアンマウントする直前に以下の行を挿入します．
<verb>
	RAIDSTATUS=`/bin/cat /proc/mdstat | /usr/bin/grep md0`
</verb>
<!--
After all the file systems are dismounted (the root file system
'will not' dismount) add:
-->
全てのファイルシステムをアンマウントした後(ルートファイルシステムはア
ンマウント「されません」)の部分に，以下を追加します．
<verb>
	# root device remains mounted RO
	# mount dos file systems RW
	mount -n -o remount,ro /
	echo "Writing RAID read-only boot FLAG(s)."
	mount -n /dosa
	mount -n /dosc
	# create raid mounted RO flag in duplicate
	# containing the shutdown status of the raid array
	echo ${RAIDSTATUS} > /dosa/raidboot/raidstat.ro
	echo ${RAIDSTATUS} > /dosc/raidboot/raidstat.ro

	umount -n /dosa
	umount -n /dosc

	# Stop all the raid arrays (except root)
	echo "Stopping raid"
	mdstop -a
</verb>
<!--
This will cleanly stop all raid devices except root.  Root status
is passed to the next boot in <bf/raidstat.ro/.
-->
これによって，ルート以外の全ての RAID デバイスが正常に終了します．ルー
トのステータスは <bf/raidstat.ro/ に保存され，次回の起動時に参照されま
す．
<p>
<!--
The complete shutdown script from my old raid1 Slackware system follows, I
have switched raid1 to the new procedure with the /etc/raidboot.conf file.
-->
筆者が以前に RAID1 の Slackware システムで使っていたシャットダウンスク
リプトの全体を以下に示します．筆者は RAID1 から /etc/raidboot.conf ファ
イルを使う新しい方法に乗り換えています．
<verb>
#! /bin/sh
#
# rc.6          This file is executed by init when it goes into runlevel
#               0 (halt) or runlevel 6 (reboot). It kills all processes,
#               unmounts file systems and then either halts or reboots.
#
# Version:      @(#)/etc/rc.d/rc.6      1.50    1994-01-15
#
# Author:       Miquel van Smoorenburg <miquels@drinkel.nl.mugnet.org>
# Modified by:  Patrick J. Volkerding, <volkerdi@ftp.cdrom.com>
# Modified by:  Michael A. Robinton, <michael@bzs.org> for RAID shutdown

  # Set the path.
  PATH=/sbin:/etc:/bin:/usr/bin

  # Set linefeed mode to avoid staircase effect.
  stty onlcr

  echo "Running shutdown script $0:"

  # Find out how we were called.
  case "$0" in
        *0)
                message="The system is halted."
                command="halt"
                ;;
        *6)
                message="Rebooting."
                command=reboot
                ;;
        *)
                echo "$0: call me as \"rc.0\" or \"rc.6\" please!"
                exit 1
                ;;
  esac

  # Kill all processes.
  # INIT is supposed to handle this entirely now, but this didn't always
  # work correctly without this second pass at killing off the processes.
  # Since INIT already notified the user that processes were being killed,
  # we'll avoid echoing this info this time around.
  if [ "$1" != "fast" ]; then # shutdown did not already kill all processes
    killall5 -15 
    killall5 -9
  fi

  # Try to turn off quota and accounting.
  if [ -x /usr/sbin/quotaoff ]
  then
        echo "Turning off quota."
        /usr/sbin/quotaoff -a
  fi
  if [ -x /sbin/accton ]
  then
        echo "Turning off accounting."
        /sbin/accton
  fi

  # Before unmounting file systems write a reboot or halt record to wtmp.
  $command -w

  # Save localtime
  [ -e /usr/lib/zoneinfo/localtime ] &amp;&amp; cp /usr/lib/zoneinfo/localtime /etc

  # Asynchronously unmount any remote filesystems:
  echo "Unmounting remote filesystems."
  umount -a -tnfs &amp;

  # you must have issued
  # 'cat /proc/mdstat | grep md0 > {your boot vol}/raidboot/raidgood.ref'  
  # before linuxrc will execute properly with this info
  RAIDSTATUS=`/bin/cat /proc/mdstat | /usr/bin/grep md0 # capture raid status`

  # Turn off swap, then unmount local file systems.
  # clearing mdtab as well
  echo "Turning off swap."
  swapoff -a
  echo "Unmounting local file systems."
  umount -a -tnonfs

  # Don't remount UMSDOS root volumes:
  if [ ! "`mount | head -1 | cut -d ' ' -f 5`" = "umsdos" ]; then
    mount -n -o remount,ro /
  fi

  # root device remains mounted
  # mount dos file systems RW
  echo "Writing RAID read-only boot FLAG(s)."
  mount -n /dosa
  mount -n /dosc
  # create raid mounted RO flag in duplicate
  # containing the shutdown status of the raid array
  echo ${RAIDSTATUS} > /dosa/raidboot/raidstat.ro
  echo ${RAIDSTATUS} > /dosc/raidboot/raidstat.ro

  umount -n /dosa
  umount -n /dosc

  # Stop all the raid arrays (except root)
  echo "Stopping raid"
  mdstop -a

  # See if this is a powerfail situation.
  if [ -f /etc/power_is_failing ]; then
    echo "Turning off UPS, bye."
    /sbin/powerd -q
    exit 1
  fi

  # Now halt or reboot.
  echo "$message"
  [ ! -f /etc/fastboot ] &amp;&amp; echo "On the next boot fsck will be FORCED."
  $command -f
</verb>


<sect>付録 E: Gadi 氏の RAID 停止に関するLinux カーネルパッチ <label id="Appendix-E">
<!-- Appendix E. - Gadi's raid stop patch for the linux kernel <label
id="Appendix-E">
-->
<p>
<verb>
--- linux/drivers/block/md.c.old        Fri Nov 21 13:37:11 1997
+++ linux/drivers/block/md.c    Sat Dec  6 13:34:28 1997
@@ -622,8 +622,13 @@
       return do_md_run (minor, (int) arg);
 
     case STOP_MD:
-      return do_md_stop (minor, inode);
-      
+      err = do_md_stop(minor, inode);
+      if (err) {
+        printk("md: enabling auto mdstop for %s\n",
kdevname(inode->i_rdev));
+        md_dev[minor].auto_mdstop = 1;
+      }
+      return err;
+
     case BLKGETSIZE:   /* Return device size */
     if  (!arg)  return -EINVAL;
     err=verify_area (VERIFY_WRITE, (long *) arg, sizeof(long));
@@ -692,6 +697,10 @@
 
   sync_dev (inode->i_rdev);
   md_dev[minor].busy--;
+  if (!md_dev[minor].busy &amp;&amp; md_dev[minor].auto_mdstop) {
+       do_md_stop(minor, inode);
+       md_dev[minor].auto_mdstop = 0;
+  }
 }
 
 static int md_read (struct inode *inode, struct file *file,
--- linux/include/linux/md.h~   Fri Nov 21 13:29:14 1997
+++ linux/include/linux/md.h    Fri Nov 21 13:29:14 1997
@@ -260,6 +260,7 @@
   int                  repartition;
   int                  busy;
   int                  nb_dev;
+  int                  auto_mdstop;
   void                 *private;
 };
</verb>
<sect>付録 F: rc.raidown <label id="Appendix-F">
<!--
Appendix F. - rc.raidown <label id="Appendix-F">
-->

<p>
<!--
Copy the following text into the script file <bf/rc.raidown/ and save it in
<bf>/etc/rc.d</bf>.
-->
以下のテキストを <bf/rc.raidown/ スクリプトとして，<bf>/etc/rc.d</bf> 
にセーブします．
<verb>
#! /bin/sh
#
# rc.raidown	This file is executed by init when it goes into runlevel
#		0 (halt) or runlevel 6 (reboot). It saves the status of
#		a root mounted raid array for subsequent re-boot
#
# Version:	1.08	3-25-98 Michael A. Robinton < michael@bizsystems.com >
#
############ Save raid boot and status info ##############
if [ -f /etc/raidboot.conf ]
then
  {
  read RaidBootDevs
  read RaidStatusPath
  read RaidConfigEtc
  } < /etc/raidboot.conf

# you must have issued
#       cat /proc/mdstat | grep md0 >
#               {your boot vol mnt(s)}/{RaidStatusPath}/raidgood.ref
# before linuxrc will execute properly with this info
#
#	capture raid status
  RAIDSTATUS=`/bin/cat /proc/mdstat | /usr/bin/grep md0`
  mkdir /tmp/raid$$
  echo "Writing RAID read-only boot FLAG(s)."
  for Device in ${RaidBootDevs}
  do
# get mount point for raid boot device or use tmp
    RBmount=$( cat /proc/mounts | /usr/bin/grep ${Device} )
    if [ -n ${RBmounts} ]; then
      RBmount=$( echo ${RBmount} | cut -f 2 -d ' ' )
    else
      RBmount="/tmp/raid$$"
      mount ${Device} ${RBmount}
    fi
  if [ -d ${RBmount}/${RaidStatusPath} ]; then
# Create raid mounted RO flag = shutdown status of raid array
    echo ${RAIDSTATUS} > ${RBmount}/${RaidStatusPath}/raidboot.ro
# Don't propagate 'fstab' from ramdisk
    if [ -f /linuxrc ]; then
      FSTAB=
    else
      FSTAB=fstab
    fi
    pushd /etc
# Save etc files for rescue system
    /bin/tar --ignore-failed-read \
	-cf ${RBmount}/${RaidStatusPath}/raidboot.etc \
	raid*.conf mdtab* ${FSTAB} lilo.conf
    popd
# Create new raidboot.cfg
    {
    /bin/echo ${RaidBootDevs}
    /bin/echo ${RaidStatusPath}
    /bin/echo ${RaidConfigEtc}
    } > ${RBmount}/${RaidStatusPath}/raidboot.cfg
    /bin/umount ${RBmount}
  fi
  done
  rmdir /tmp/raid$$
  echo "Raid boot armed"
fi
################## end raid boot #########################
</verb>
<sect>付録 G: linuxrc の動作原理<label id="Appendix-G">
<!--
Appendix G. - linuxrc theory of operation <label id="Appendix-G">
-->
<p>
<!--
 This is the complex form of the linuxrc file for root mounted raid.
 It must be processed with 'bash' or another shell that recognizes
 shell functions.
-->
 これは RAID をルートファイルシステムにマウントするための，linuxrc ファ
 イルの複雑な形のものです．このファイルは `bash' か，それ以外のシェル
 関数が利用できるシェル上で実行しなければなりません．
<p>
<!--
 The advantage is that it is generic and is not dependent on startup
 files and parameters located in the <bf/initrd/ image.
-->
 この利点は，一般的であり，<bf/initrd/ イメージ内にあるスタートアップ
 ファイルやパラメータに依存しないことです．
<p>
<!--
 A <bf/Raid_Conf/ parameter passed to <bf/linuxrc/ by the kernel at boot 
 from lilo or loadlin contains a pointer to the boot devices and 
location the of
 initial 2 raidboot files needed by <bf/linuxrc/ (<it>raidboot.etc and
raidboot.cfg placed by the shutdown script</it>).
-->
 ブート時にカーネルによって LILO や loadlin から<bf/linuxrc/ に渡され
た <bf/Raid_Conf/ パラメータは，<bf/linuxrc/ が必要とする起動デバイス
や raidboot の2つの初期化ファイルの位置を示します(<it>raidboot.etc と 
raidboot.cfg はシャットダウンスクリプトによって作られます)．
<quote>
<!--
 <bf/raidboot.etc/ containing the 'tar'ed files:
-->
 <bf/raidboot.etc/ は元となるシステムから以下に示すファイルを tar でま
とめたもので，起動時に initrd の <bf>/etc</bf>ディレクトリになります．
<verb>
	raid*
	mdtab*
	fstab
	lilo.conf		( 利用可能ならば )
</verb>
<!--
from the primary system that are transferred to the
 initrd <bf>/etc</bf>etc directory at startup. With care, this file may
 be edited if necessary when your system 'really' crashes.
-->
注意すべき点は，このファイルはシステムが「本当に」クラッシュしたときに
は，必要に応じて編集される点です．
<p>
<!--
<bf/raidboot.cfg/ contains the name of the boot partition in use
 and applicable backup(s) as well as the path to the rest of 
 the raid start up file used by <bf/linuxrc/.
 This file is normally created by the shutdown file
 and may be created manually if necessary.
-->
<bf/raidboot.cfg/ は <bf/linuxrc/ が必要とする残りの RAID 起動ファイル
のパスと，使用されているブートパーティション及び利用可能なバックアップ
パーティションの名前を持っています．このファイルは通常，シャットダウン
ファイルによって作成されますが，必要に応じて手動で作ることもあります．
<p>
<!--
<bf/raidboot.cfg/ is of the form, 3 lines - no comments
-->
<bf/raidboot.cfg/ は3行，コメント無しの形式です．
<!--
<verb>
	/dev/bootdev1 /dev/bootdev2 [/dev/bootdev3 ... and so on]
	raid-status/path 
	name_of_raidX.conf_file
</verb><quote>
-->
<verb>
	/dev/bootdev1 /dev/bootdev2 [/dev/bootdev3 ... 等]
	raid-status/path 
	name_of_raidX.conf_file
</verb><quote>
<!--
  the <bf>raid-status/path</bf> does not include the name of the mountpoint     
-->
  <bf>raid-status/path</bf> はマウントポイントの名前は含みません．
<p>
<!--
  the <bf/raidX.conf/ filename is that one found in /etc 
  and normally used for <bf/ckraid/ and <bf/mkraid/.
-->
  <bf/raidX.conf/ のファイル名は /etc ディレクトリ内のもので，通常は 
  <bf/ckraid/ と <bf/mkraid/ のために用いられます．
</quote></quote>
<!--
  The following additional files reside on the permanent raid boot partitions.
  This is usually the same as above, but in emergency situations
  may be loaded from anywhere they are available, such as a floppy boot disk.
-->
  以下の追加ファイルは，ずっと使用する RAID 起動パーティションに置きま
  す．これは上で述べたのと同じものですが，非常事態には利用可能な任意の
  場所(例えば起動フロッピーディスク)からロードすることができます．
<!--
<itemize>
<item><bf/raidgood.ref/ created by the command
 cat /proc/mdstat | grep md0 > /{raid_status_path}/raidgood.ref
<p>	
 See the <ref id="modify_shutdown" name="shutdown scripts">
 for saving this file and the next
<p>
<item><bf/raidstat.ro/ created at each shutdown by the shutdown rc file,
 saving the exit status of the raid array.
</itemize>
-->
<itemize>
<item><bf/raidgood.ref/ は次のコマンドによって作成されます．
 cat /proc/mdstat | grep md0 > /{raid_status_path}/raidgood.ref
<p>	
 このファイルとこの次のファイルをセーブする場合は，<ref
id="modify_shutdown" name="シャットダウンスクリプト">の章を参照してく
ださい．
<p>
<item><bf/raidstat.ro/ はシャットダウン時に毎回 rc スクリプトによって
作成され，RAID アレイの終了ステータスを保存します．
</itemize>

</article>
