Daily GLOWBUGS
Digest: V1 #103
via AB4EL Web Digests @ SunSITE
Purpose: building and operating vacuum tube-based QRP rigs
Subject: glowbugs V1 #103
glowbugs Wednesday, September 3 1997 Volume 01 : Number 103
Date: Tue, 2 Sep 1997 10:31:18 -0400 (EDT)
From: EWoodman@aol.com
Subject: 6M Receive Converter
Hi all,
Does anyone, in their piles of old handbooks or magazines, happen to have a
schematic for a 6 meter receive converter? The solid state one that I slapped
together works, but not that well, and is not exactly in keeping with the
spirt of the old glowing stuff.
Tnx and 73,
Eric KA1YRV
Date: Tue, 2 Sep 1997 09:22:09 -0700 (MST)
From: Jeff Duntemann <jeffd@coriolis.com>
Subject: The weekend's homebrewing
Hi gang--
Halfway through the long weekend I actually ran out of "important" things
to do. Egad! Headed for the garage at 40% the speed of light, left
standing waves in the dirt.
I pulled out my 6AG7/6L6 80M transmitter lashup off the short-list shelf
and fired it up to make sure it still worked. 16 watts out, as before.
For fun I pulled a greasy old 6DQ5 sweep tube from the bin, rewired a
couple of pins on the octal socket (this is my PCB board-based prototyping
system that I've described here before) added a plate cap, parasitic
suppressor, and better plate choke (actually the three are a unit unearthed
in the junkbox, obviously "removed from equipment" tho heaven knows what)
and without any further changes to the circuit applied power. 20+ watts
out, looked clean and parasitic-free. However, my poor bench supply was
groaning a little; the 440 V B+ was being pulled down to 210V by the 130 ma
load, and the unregulated screen voltage was down to 75V! (It's really
only a 100 ma supply.)
But my curiosity was piqued (not peaked, as in an IF can; made that mistake
before in my magazine and got reamed out for it...) and I hauled out the
middling homebrew supply I got for a dollar at Flagstaff '96 and mentioned
here once before. I finished adding two OD3/VR150s to it, giving me both
300V and 150V regulated, plus 450V B+ at considerably higher current than
my smaller bench supply--judging by the power transformer and chokes, I
would guess it could give me 150-175 ma at least, maybe 200.
About all I had to do to the circuit was pull out the screen dropping
resistor and hook the screen to the new regulated 150V output. Shazam!
36W output, still clean. I haven't measured the screen current yet so I
can't quote power input or efficiency. (Eventually I did run out of
weekend...) Plate input alone is about 50W.
Anyway, watt-quibbling aside, this is seriously cool, considering I was
using a fairly common junkbox tube that's actually cheaper than a good 6L6.
($9 from Alltronics.)
My intuition is that the tube can supply a little more power than this, and
the next step is to rebuild the oscillator stage so that there's a tuned
input to the final. The ultimate goal is a 75W input box for 80, 40, and
20. I think I'm most of the way there. At least I now have the power supply.
Haven't had a chance to do much of this all summer. I guess autumn is
finally upon us.
- --73--
- --Jeff Duntemann KG7JF
Scottsdale, Arizona
Date: Wed, 03 Sep 1997 19:49:03 EDT
From: km1h@juno.com (km1h @ juno.com)
Subject: Re: Dentron GLA-1000 B linear
The following is copied from another reflector. W6NQ is the owner of RF
Parts Co.
At only $ 30 ea for the Russian ($20 for the Yugo) it may be an
attractive tube for the power obtainable.
A 40V filament version is also available at the same price which "could"
make a transformerless PS 3 tube amp possible to the adventuresome.
73....Carl KM1H
- --------- Begin forwarded message ----------
Just a general observations on the EL509 in replacing 6LQ6:
We have played around with various manufacturers of this tube.
The tube is quite a bit larger in size.
The Russian made tube is the most rugged (vs. Yugo, etc.)
I think it was used as a voltage regulator in USSR tank transmitters.
The original Russian tube number is not EL509, but this number
has been applied for the "TV Sweep" applications, i.e. linear amps.
You can expect about half the drive requirement to achieve same output.
You can also expect lots of p.e.p. The EL509 is 40W dissipation.
However, this tube is easy to kill with excessive drive.
Be sure to improve cooling, bias mods, etc.
It will plug into most 6LQ6 sockets if you enlarge socket holes a bit
(dental tool).
Regards, Merit W6NQ (W6NLO)
End of glowbugs V1 #103
***********************
Created by Steve Modena, AB4EL
Comments and suggestions to modena@SunSITE.unc.edu