From gerry@msage.com  Mon Jun 20 14:31:17 1994
Received: by altair.krl.caltech.edu; id AA29826; Mon, 20 Jun 1994 14:31:17 -0700
Received: by heifetz.msen.com with UUCP (Smail3.1.28.1 #12)
	id m0qFqgn-000ZVAC; Mon, 20 Jun 94 17:15 EDT
From: gerry@msage.com (Gerry Duprey)
Date: Mon, 20 Jun 1994 17:04:27 -0400
Message-Id: <9406202104.AA14629@>
In-Reply-To: Tim Shoppa <shoppa@altair.krl.caltech.edu>
       "Re: Emulex TC02's" (Jun 20, 11:41am)
X-Mailer: Mail User's Shell (6.4 2/14/89)
To: Tim Shoppa <shoppa@altair.krl.caltech.edu>
Subject: Re: Emulex TC02's
Status: RO

Hi Tim,

	This is from the back of the TC02 manual

	OFF	ON
	OPEN	CLOSED	Description
 	------- ------- -----------------------------------------
SW1-1 	Run	Reset	Coupler Reset
SW1-2	Disable	Enable	22 Bit addressing mode (must have 22 bit rom)
SW1-3	Disable	Enable	3200 bpi density support
SW1-4	Stream	Format	Drive type (streamer or formatter)

	Factory setting is all switches open/OFF

        OFF     ON
        OPEN    CLOSED  Description
        ------- ------- -----------------------------------------
SW2-1	1	0	Vector Bit #2
SW2-2	1	0	"	   #3
SW2-3	1	0	"	   #4
SW2-4	1	0	"          #5
SW2-5	1	0	"	   #6
SW2-6	1	0	"	   #7
SW2-7	1	0	"	   #8
SW2-8		224	Unit 0 Vector address
SW2-9	Disable	Enable	Long interblock Gap Enable
SW2-10	Disable	Enable	CDC extended status and GCR operation

	(factory setting is SW2-8 On/Close, all others Off/Open)

        OFF     ON
        OPEN    CLOSED  Description
        ------- ------- -----------------------------------------
SW3-1		772520	Standard Qbus Address
SW3-2		772440	Alternate QBus Address
SW3-3	Disable	Enable	Unit 1 enabled
SW3-4	Disable	Enable	Unit 2 enabled
SW3-5	Disable	Enable	Unit 3 enabled
SW3-6	Disable	Enable	Unit 4 enabled
SW3-7	>50ips	<=50ips	Tape drive speed select
SW3-8	Disable	Enable	Inhibit on the fly commands
SW3-9			Not used
SW3-10	2K	4K	PROM Address range

	(factory setting is SW3-1,-3,-7 on/closed all others Off/open)

	The TC02 also supports a very nice little boot strap loader.  If
you pump the following into it, it'll skip the 1st record and the tape and
load the 2nd into memory start at 0.  It goes like this:

	0/0 <CR>	; set a reset into location 0
	0G		; execute a reset 
	000002		; echoed after 0G (reset)
	17772522/100001 <CR>
	17772522/100001 <CR>	; tape should advance - 1st block loaded
	$6/10000 <CR>		; Set stack pointer
	0G			; start boot.  Some O/S need CSR and unit
				; in R0 and R1.

	I'm sure you can do this with a VAX as there is nothing to PDP
about it.

	Let me know if you have any problems or questions.  Good luck!
	
	

-- 
Gerry Duprey                     EMAIL: gerry@msage.com 
Micro Sage Software Systems      VOICE: (313) 663-0444
130 South First Street
Ann Arbor, MI 48104 USA


