================================ INSTALLATION NOTES FOR BOGUS 1.0 ================================ Here is the procedure to boot with the boot disks: 1. Boot with boot disk #1 2. Login as root 4. Insert disk #2 in drive #1 3. get_files 5. logout 6. Login as root [tcsh] or toor [bash] 7. NOTE: Only /dev/sda and /dev/sdb are created on the boot disks, so those with more than two SCSI hard drives (or those who need other devices) should create them with: cd /dev; ./MAKEDEV [device name] Here is the procedure to get your system to boot from the hard disk: 1. Boot with the boot disks [see above] 2. Run fdisk on the drive you want to use for linux 3. Create partitions for / and /usr [required] 4. Create partition for swap [optional] 5. Create partitions for /var, /usr/src, /usr/local, /home, and /playpen [optional] 6. Reboot with boot disks so that partitions take effect 7. Choose fs type for each partition created [minix, ext2, ...] 8. Run mkfs for each partition created 9. Run mkswap on swap device [optional] 10. Mount / partition on /mnt 11. mkdir /mnt/usr /mnt/var /mnt/home /mnt/playpen [playpen is optional] 12. Mount /usr partition on /mnt/usr 13. Mount /var partition on /mnt/var [optional] 14. Mount /home partition on /mnt/home [optional] 15. Mount /playpen partition on /mnt/playpen [optional] 16. mkdir /mnt/usr/local /mnt/usr/src 17. Mount /usr/src partition on /mnt/usr/src [optional] 18. Mount /usr/local partition on /mnt/usr/local [optional] 19. make_system 20. NOTE: Just as with the boot disk, only /dev/sda and /dev/sdb are created on the hard drive, so those with more than two SCSI hard drives (or those who need other devices) should create them with: cd /mnt/dev; ./MAKEDEV [device name] 21. Edit /mnt/etc/fstab 22. Edit /mnt/etc/lilo.conf 23. sh -c 'ROOT=/mnt /mnt/sbin/lilo' 24. Reboot from hard disk by booting from boot disk #1 and when the LILO prompt appears, pressing the Shift key. This will allow you to enter "linux root=/dev/XXXX" where XXXX is the / partition. Here is the procedure to install the rest of BOGUS: 1. mkdir /usr/src/DIST 2. Copy all of the binary files to /usr/src/DIST from tape or disk or ... 3. /usr/src/scripts/install.all 4. NOTE: If you are using tcsh, you will need to "rehash". 5. Configure, rebuild and install a new kernel. 6. lilo 7. Edit /etc/rc.local and change the hostname and domainname lines to reflect your host and domain names. 8. If you installed the networking kits, a. cp /usr/doc/utils/NetKit-A-0.04/config/* /etc b. ln -sf /etc/issue /etc/issue.net c. Add your host database to /etc/hosts d. Add your network to /etc/networks e. Add your nameserver to /etc/resolv.conf f. Edit /etc/net.conf to setup your network controller and to start the appropriate daemons. g. Edit /etc/printcap to add your printers (add filters as necessary) h. touch /etc/NETWORKING_IS_ON 9. If your date is incorrect, a. date [MMDDhhmm] b. clock -w 10. If you installed the XFree86 system, a. cp /usr/lib/X11/Xconfig.sample /etc/Xconfig b. Edit /etc/Xconfig for your system. c. ln -sf /usr/X386/bin/[Your X server] /usr/X386/bin/X d. NOTE: If your mouse is not in /dev, you need to create it with MAKEDEV in /dev. 11. If you installed InterViews, a. Add /usr/interviews/lib/LINUX to /etc/ld.so.conf b. ldconfig 12. If you installed TeX, edit /usr/lib/texmf/dvips/config.ps for you printer. 13. ln -s /dev/[Your modem device] /dev/modem 14. ldconfig 15. update_state [Note: This script will take some time while it builds the appropriate database files] 16. Reboot 17. Verify that everything installed properly and is set up properly.